Проблемы с настройкой Internet на 2 пк.

Сообщений: 16, участников: 4

Ответить

27 апреля 2011, 10:28 linux user Записей: 15	Здравствуйте! Прошу сильне не пинать, если создал новую тему, но по своей проблеме не нашел ответа. Временно приходится работать системным администратором (если так можно сказать) в школе. Но с Linux я не дружу вообще. Всю жизнь возился с Windows, начиная с 98го и по нынешний день. А тут переход школ на ПО с открытым кодом и, отсюда, как следствие неумения работать с таковым ПО - проблемы. Пожалуйста, прошу, помогите и не ругайте сильно, с Linux я даже не на Вы... Итак проблема. Имеется компьютерный класс. Интернет по технологии ADSL. Модем Huawei HG520, от него (кабелем, не по WI-FI, а именно сетевым кабелем) через коммутатор Corega FSW-16PM сетевые кабели подводятся к компьютерам. Установил EduMandriva на компьютеры. Поочередно, начиная с сервера, стал вбивать IP адреса (10.31.90.66, на втором пк 10.31.90.67, и т.д.) и DNS (10.0.0.1/10.0.0.2) и маску подсети (255.255.255.224), естественно. Все хорошо. Везде Интернет есть, кроме двух компьютеров. При попытке ввести IP адреса появляется сообщение с заголовком Drakconnect, о том, что: "Невозможно найти сетевой интерфейс для выбранного устройства (используя драйвер е1000е)". Заметил, что на этих 2 компьютерах сетевая карта распознается как 82566 DC-2 Gigabyte Ethernet Adapter, а на все остальных пк (где Internet завелся сразу после того, как прописал IP), сетевая карта 82566 DM-2 (пишу по памяти, но вроде верно, отличие в одной букве). Полез на сайт Intel, скачал свежие драйвера для этой сетевой карты 82566 DM-2 под Linux, и дело встало, так как, банально, не смог установить их, не зная команд при работе с терминалом. А может дело и не в драйверах вовсе? Помогите разобраться, пожалуйста. Если можно - максимально просто, что нужно нажать, куда что прописать, чтоб исправить положение. Кстати, материнская плата Gigabyte GA-Q35M-S2 на всех пк. А вот сетевая карта на 2 пк распознается немножко по другому. Не пойму, то ли это действительно проблема корректного распознавания карты Linux'ом, то ли просто чип самой сетевушки немножко другой модицикации. И вот куда копать? :) Вероятно, все на самом деле просто, но для человека, который пару раз в жизни видел Linux, все как раз наоборот, очень-очень сложно. Заранее спасибо. Направлено в техническую поддержку 10 октября 2011, 15:44.

27 апреля 2011, 12:19 akdengi Записей: 96	На тех машинах, где нет интернета в эмуляторе терминала (скорее всего у вас lxterminal или konsole) введите lspci -k и дайте сюда вывод - посмотрим на сетевую и ее поддержку.

27 апреля 2011, 15:57 Julia Dronova (administrator) Записей: 3144	На всякий случай для тех, то только начинает работу с Линукс, более подробно о том, как вообще работать с выводом консоли: ТУТ Что-то непонятное -- спрашивайте.

28 апреля 2011, 15:20 linux user Записей: 15	1 пк [schoolchild@localhost ~]$ lspci -k 00:00.0 Host bridge: Intel Corporation 82Q35 Express DRAM Controller (rev 02) Subsystem: Giga-byte Technology Device 5000 00:01.0 PCI bridge: Intel Corporation 82Q35 Express PCI Express Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:03.0 Communication controller: Intel Corporation 82Q35 Express MEI Controller (rev 02) Subsystem: Giga-byte Technology Device 29b4 Kernel driver in use: heci Kernel modules: heci 00:03.2 IDE interface: Intel Corporation 82Q35 Express PT IDER Controller (rev 02) Subsystem: Giga-byte Technology Device 29b6 00:03.3 Serial controller: Intel Corporation 82Q35 Express Serial KT Controller (rev 02) Subsystem: Giga-byte Technology Device 29b7 Kernel driver in use: serial 00:19.0 Ethernet controller: Intel Corporation 82566DC-2 Gigabit Network Connection (rev 02) Subsystem: Intel Corporation Device 0000 Kernel modules: e1000e 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) Subsystem: Giga-byte Technology Device 5006 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) Subsystem: Giga-byte Technology Device a002 Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) Subsystem: Giga-byte Technology Device 5006 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IO (ICH9DO) LPC Interface Controller (rev 02) Subsystem: Giga-byte Technology Device 5001 Kernel modules: iTCO_wdt 00:1f.2 IDE interface: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 4 port SATA IDE Controller (rev 02) Subsystem: Giga-byte Technology Device b002 Kernel driver in use: ata_piix Kernel modules: ata_piix 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) Subsystem: Giga-byte Technology Device 5001 Kernel driver in use: i801_smbus Kernel modules: i2c-i801 00:1f.5 IDE interface: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller (rev 02) Subsystem: Giga-byte Technology Device b002 Kernel driver in use: ata_piix Kernel modules: ata_piix 01:00.0 VGA compatible controller: ATI Technologies Inc Mobility Radeon HD 3600 Series Subsystem: Hightech Information System Ltd. Device 2002 Kernel driver in use: fglrx_pci Kernel modules: fglrx 01:00.1 Audio device: ATI Technologies Inc RV635 Audio device [Radeon HD 3600 Series] Subsystem: Hightech Information System Ltd. Device aa20 Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 03:00.0 IDE interface: JMicron Technology Corp. JMB368 IDE controller Subsystem: Giga-byte Technology Device b000 Kernel driver in use: pata_jmicron Kernel modules: pata_jmicron, jmicron 2 пк [schoolchild@localhost ~]$ lspci -k 00:00.0 Host bridge: Intel Corporation 82Q35 Express DRAM Controller (rev 02) Subsystem: Giga-byte Technology Device 5000 00:01.0 PCI bridge: Intel Corporation 82Q35 Express PCI Express Root Port (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:03.0 Communication controller: Intel Corporation 82Q35 Express MEI Controller (rev 02) Subsystem: Giga-byte Technology Device 29b4 Kernel modules: heci 00:03.2 IDE interface: Intel Corporation 82Q35 Express PT IDER Controller (rev 02) Subsystem: Giga-byte Technology Device 29b6 00:03.3 Serial controller: Intel Corporation 82Q35 Express Serial KT Controller (rev 02) Subsystem: Giga-byte Technology Device 29b7 Kernel driver in use: serial 00:19.0 Ethernet controller: Intel Corporation 82566DC-2 Gigabit Network Connection (rev 02) Subsystem: Intel Corporation Device 0000 Kernel modules: e1000e 00:1a.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1a.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1a.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1a.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 02) Subsystem: Giga-byte Technology Device 5006 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 02) Subsystem: Giga-byte Technology Device a002 Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 02) Kernel driver in use: pcieport Kernel modules: shpchp 00:1d.0 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.1 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.2 USB Controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 02) Subsystem: Giga-byte Technology Device 5004 Kernel driver in use: uhci_hcd Kernel modules: uhci-hcd 00:1d.7 USB Controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 02) Subsystem: Giga-byte Technology Device 5006 Kernel driver in use: ehci_hcd Kernel modules: ehci-hcd 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 92) 00:1f.0 ISA bridge: Intel Corporation 82801IO (ICH9DO) LPC Interface Controller (rev 02) Subsystem: Giga-byte Technology Device 5001 Kernel modules: iTCO_wdt 00:1f.2 IDE interface: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 4 port SATA IDE Controller (rev 02) Subsystem: Giga-byte Technology Device b002 Kernel driver in use: ata_piix Kernel modules: ata_piix 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 02) Subsystem: Giga-byte Technology Device 5001 Kernel driver in use: i801_smbus Kernel modules: i2c-i801 00:1f.5 IDE interface: Intel Corporation 82801I (ICH9 Family) 2 port SATA IDE Controller (rev 02) Subsystem: Giga-byte Technology Device b002 Kernel driver in use: ata_piix Kernel modules: ata_piix 01:00.0 VGA compatible controller: ATI Technologies Inc Mobility Radeon HD 3600 Series Subsystem: Hightech Information System Ltd. Device 2002 Kernel driver in use: fglrx_pci Kernel modules: fglrx 01:00.1 Audio device: ATI Technologies Inc RV635 Audio device [Radeon HD 3600 Series] Subsystem: Hightech Information System Ltd. Device aa20 Kernel driver in use: HDA Intel Kernel modules: snd-hda-intel 03:00.0 IDE interface: JMicron Technology Corp. JMB368 IDE controller Subsystem: Giga-byte Technology Device b000 Kernel driver in use: pata_jmicron Kernel modules: pata_jmicron, jmicron [schoolchild@localhost ~]$ походу, проблема с драйвером ?

03 мая 2011, 12:08 akdengi Записей: 96	Попробуйте от root дать команду modprobe -l \| grep e1000e и сюда вывод. Также можно попробовать просто включить модуль драйвера modprobe e1000e

10 мая 2011, 15:20 linux user Записей: 15	[root@localhost schoolchild]# modprobe -l\|grep e1000e kernel/drivers/net/e1000e/e1000e.ko.gz включение драйвера не помогло.

10 октября 2011, 15:36 linux user Записей: 15	Все еще актуально... Помогите, пожалуйста.

10 октября 2011, 15:44 Julia Dronova (administrator) Записей: 3144	linux user писал(а): Все еще актуально... Помогите, пожалуйста. Перенаправила первый пост темы в техподдержку.

10 октября 2011, 21:33 Школа8 Записей: 862	linux user писал(а): Все еще актуально... Помогите, пожалуйста. Еще можно dmesg >filedmesg.txt на здоровой машине и на больной и два файла filedmesg.txt сюда ?

13 октября 2011, 15:35 linux user Записей: 15	Каким тегом поместить текст под спойлер? или как файлы сюда прикреплять?

13 октября 2011, 15:49 Julia Dronova (administrator) Записей: 3144	linux user FAQ по форуму

13 октября 2011, 16:27 linux user Записей: 15	Компьютер на котором есть интернет [root@localhost schoolchild]# dmesg Linux version 2.6.33.7-desktop586-2mnb (qateam@titan.mandriva.com) (gcc version 4.4.3 (GCC) ) #1 SMP Mon Sep 20 18:19:58 UTC 2010 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000007deb0000 (usable) BIOS-e820: 000000007deb0000 - 000000007dee3000 (ACPI NVS) BIOS-e820: 000000007dee3000 - 000000007def0000 (ACPI data) BIOS-e820: 000000007def0000 - 000000007df00000 (reserved) BIOS-e820: 00000000d0000000 - 00000000e0000000 (reserved) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel! DMI 2.4 present. last_pfn = 0x7deb0 max_arch_pfn = 0x100000 MTRR default type: uncachable MTRR fixed ranges enabled: 00000-9FFFF write-back A0000-BFFFF uncachable C0000-CEFFF write-protect CF000-EFFFF uncachable F0000-FFFFF write-through MTRR variable ranges enabled: 0 base 000000000 mask F80000000 write-back 1 base 07E000000 mask FFE000000 uncachable 2 base 07DF00000 mask FFFF00000 write-through 3 disabled 4 disabled 5 disabled 6 disabled 7 disabled x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 initial memory mapped : 0 - 00c00000 found SMP MP-table at [c00f5580] f5580 init_memory_mapping: 0000000000000000-00000000373fe000 0000000000 - 0000400000 page 4k 0000400000 - 0037000000 page 2M 0037000000 - 00373fe000 page 4k kernel direct mapping tables up to 373fe000 @ 7000-d000 RAMDISK: 37af0000 - 37fefa9a Allocated new RAMDISK: 00804000 - 00d03a9a Move RAMDISK from 0000000037af0000 - 0000000037fefa99 to 00804000 - 00d03a99 ACPI: RSDP 000f73f0 00014 (v00 Dealin) ACPI: RSDT 7dee3040 0004C (v01 Dealin depo 42302E31 GBTU 01010101) ACPI: FACP 7dee30c0 00074 (v01 Dealin depo 42302E31 GBTU 01010101) ACPI: DSDT 7dee3180 059CF (v01 DEALIN DEPO 00001000 MSFT 0100000C) ACPI: FACS 7deb0000 00040 ACPI: SLIC 7dee8cc0 00176 (v01 Dealin depo 42302E31 GBTU 01010101) ACPI: ASF! 7dee8e80 0008A (v16 Dealin depo 42302E31 GBTU 00000000) ACPI: HPET 7dee8f80 00038 (v01 Dealin depo 42302E31 GBTU 00000098) ACPI: MCFG 7dee9000 0003C (v01 Dealin depo 42302E31 GBTU 01010101) ACPI: TCPA 7dee9080 00032 (v01 HTC HTCACPI 42302E31 GBTU 00000000) ACPI: APIC 7dee8bc0 00084 (v01 Dealin depo 42302E31 GBTU 01010101) ACPI: SSDT 7dee9100 0019E (v01 PmRef Cpu0Ist 00003000 INTL 20040311) ACPI: DMAR 7dee9590 000D0 (v01 IntelR AWRDACPI 30302E32 AWRD 00000001) ACPI: DMAR 7dee9590 000D0 (v01 IntelR AWRDACPI 30302E32 AWRD 00000001) ACPI: Local APIC address 0xfee00000 1130MB HIGHMEM available. 883MB LOWMEM available. mapped low ram: 0 - 373fe000 low ram: 0 - 373fe000 node 0 low ram: 00000000 - 373fe000 node 0 bootmap 0000a000 - 00010e80 (14 early reservations) ==> bootmem [0000000000 - 00373fe000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] #2 [0000100000 - 00007ff0e4] TEXT DATA BSS ==> [0000100000 - 00007ff0e4] #3 [0000800000 - 00008030c2] BRK ==> [0000800000 - 00008030c2] #4 [00000f5590 - 0000100000] BIOS reserved ==> [00000f5590 - 0000100000] #5 [00000f5580 - 00000f5590] MP-table mpf ==> [00000f5580 - 00000f5590] #6 [000009f800 - 00000f0d00] BIOS reserved ==> [000009f800 - 00000f0d00] #7 [00000f0ea4 - 00000f5580] BIOS reserved ==> [00000f0ea4 - 00000f5580] #8 [00000f0d00 - 00000f0ea4] MP-table mpc ==> [00000f0d00 - 00000f0ea4] #9 [0000002000 - 0000003000] TRAMPOLINE ==> [0000002000 - 0000003000] #10 [0000003000 - 0000007000] ACPI WAKEUP ==> [0000003000 - 0000007000] #11 [0000007000 - 000000a000] PGTABLE ==> [0000007000 - 000000a000] #12 [0000804000 - 0000d03a9a] NEW RAMDISK ==> [0000804000 - 0000d03a9a] #13 [000000a000 - 0000011000] BOOTMAP ==> [000000a000 - 0000011000] Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x000373fe HighMem 0x000373fe -> 0x0007deb0 Movable zone start PFN for each node early_node_map[2] active PFN ranges 0: 0x00000000 -> 0x0000009f 0: 0x00000100 -> 0x0007deb0 On node 0 totalpages: 515663 free_area_init_node: node 0, pgdat c063d6c0, node_mem_map c1001000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 3967 pages, LIFO batch:0 Normal zone: 1736 pages used for memmap Normal zone: 220470 pages, LIFO batch:31 HighMem zone: 2262 pages used for memmap HighMem zone: 287196 pages, LIFO batch:31 Using APIC driver default ACPI: PM-Timer IO Port: 0x408 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x02] dfl dfl lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x03] dfl dfl lint[0x1]) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Using ACPI (MADT) for SMP configuration information ACPI: HPET id: 0x8086a201 base: 0xfed00000 SMP: Allowing 4 CPUs, 2 hotplug CPUs nr_irqs_gsi: 24 PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000f0000 PM: Registered nosave memory: 00000000000f0000 - 0000000000100000 Allocating PCI resources starting at 7df00000 (gap: 7df00000:52100000) Booting paravirtualized kernel on bare hardware setup_percpu: NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:4 nr_node_ids:1 PERCPU: Embedded 14 pages/cpu @c2000000 s35416 r0 d21928 u1048576 pcpu-alloc: s35416 r0 d21928 u1048576 alloc=14194304 pcpu-alloc: [0] 0 1 2 3 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 511633 Kernel command line: BOOT_IMAGE=linux root=UUID=762167ad-6fbd-4150-b2a0-8a721a1e5efc resume=UUID=baccd61d-3c1e-4d9c-a0ba-e4a80a677833 splash=silent vga=788 PID hash table entries: 4096 (order: 2, 16384 bytes) Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 Initializing HighMem for node 0 (000373fe:0007deb0) Memory: 2031988k/2063040k available (3278k kernel code, 29532k reserved, 2210k data, 520k init, 1157832k highmem) virtual kernel memory layout: fixmap : 0xffaf4000 - 0xfffff000 (5164 kB) pkmap : 0xff400000 - 0xff800000 (4096 kB) vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB) lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB) .init : 0xc065d000 - 0xc06df000 ( 520 kB) .data : 0xc0433b6b - 0xc065c708 (2210 kB) .text : 0xc0100000 - 0xc0433b6b (3278 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. SLUB: Genslabs=13, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Hierarchical RCU implementation. NR_IRQS:2304 Console: colour dummy device 80x25 console [tty0] enabled hpet clockevent registered Fast TSC calibration using PIT Detected 2194.809 MHz processor. Calibrating delay loop (skipped), value calculated using timer frequency.. 4389.61 BogoMIPS (lpj=2194809) Security Framework initialized TOMOYO Linux initialized Mount-cache hash table entries: 512 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 mce: CPU supports 6 MCE banks CPU0: Thermal monitoring enabled (TM2) using mwait in idle threads. Performance Events: Core2 events, Intel PMU driver. ... version: 2 ... bit width: 40 ... generic registers: 2 ... value mask: 000000ffffffffff ... max period: 000000007fffffff ... fixed-purpose events: 3 ... event mask: 0000000700000003 Checking 'hlt' instruction... OK. ACPI: Checking initramfs for custom DSDT ACPI: Core revision 20091214 ftrace: converting mcount calls to 0f 1f 44 00 00 ftrace: allocating 15181 entries in 30 pages DMAR: Host address width 36 DMAR: DRHD base: 0x000000fed90000 flags: 0x0 IOMMU fed90000: ver 1:0 cap c9008020a30270 ecap 1000 DMAR: DRHD base: 0x000000fed92000 flags: 0x0 IOMMU fed92000: ver 1:0 cap c0000020230270 ecap 1000 DMAR: DRHD base: 0x000000fed93000 flags: 0x1 IOMMU fed93000: ver 1:0 cap c9008020230270 ecap 1000 DMAR: RMRR base: 0x0000007def0000 end: 0x0000007defffff DMAR: No ATSR found Enabling APIC mode: Flat. Using 1 I/O APICs ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Pentium(R) Dual CPU E2200 @ 2.20GHz stepping 0d Booting Node 0, Processors #1 Initializing CPU#1 Brought up 2 CPUs Total of 2 processors activated (8778.39 BogoMIPS). devtmpfs: initialized Time: 0:07:47 Date: 01/01/07 NET: Registered protocol family 16 ACPI: bus type pci registered PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xd0000000-0xdfffffff] (base 0xd0000000) PCI: MMCONFIG at [mem 0xd0000000-0xdfffffff] reserved in E820 PCI: Using MMCONFIG for extended config space PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0 ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) pci_root PNP0A03:00: ignoring host bridge windows from ACPI; boot with "pci=use_crs" to use them pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7] (ignored) pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0x000c0000-0x000dffff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0xfed40000-0xfed44fff] (ignored) pci_root PNP0A03:00: host bridge window [mem 0x7df00000-0xfebfffff] (ignored) pci 0000:00:01.0: PME# supported from D0 D3hot D3cold pci 0000:00:01.0: PME# disabled pci 0000:00:03.0: reg 10: [mem 0xf3027000-0xf302700f 64bit] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold pci 0000:00:03.0: PME# disabled pci 0000:00:03.2: reg 10: [io 0xd900-0xd907] pci 0000:00:03.2: reg 14: [io 0xd000-0xd003] pci 0000:00:03.2: reg 18: [io 0xd100-0xd107] pci 0000:00:03.2: reg 1c: [io 0xd200-0xd203] pci 0000:00:03.2: reg 20: [io 0xd300-0xd30f] pci 0000:00:03.3: reg 10: [io 0xd400-0xd407] pci 0000:00:03.3: reg 14: [mem 0xf3026000-0xf3026fff] pci 0000:00:19.0: reg 10: [mem 0xf3000000-0xf301ffff] pci 0000:00:19.0: reg 14: [mem 0xf3024000-0xf3024fff] pci 0000:00:19.0: reg 18: [io 0xd500-0xd51f] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold pci 0000:00:19.0: PME# disabled pci 0000:00:1a.0: reg 20: [io 0xd600-0xd61f] pci 0000:00:1a.1: reg 20: [io 0xd700-0xd71f] pci 0000:00:1a.2: reg 20: [io 0xd800-0xd81f] pci 0000:00:1a.7: reg 10: [mem 0xf3025000-0xf30253ff] pci 0000:00:1b.0: reg 10: [mem 0xf3020000-0xf3023fff 64bit] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold pci 0000:00:1b.0: PME# disabled pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold pci 0000:00:1c.0: PME# disabled pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold pci 0000:00:1c.1: PME# disabled pci 0000:00:1d.0: reg 20: [io 0xda00-0xda1f] pci 0000:00:1d.1: reg 20: [io 0xdb00-0xdb1f] pci 0000:00:1d.2: reg 20: [io 0xdc00-0xdc1f] pci 0000:00:1d.7: reg 10: [mem 0xf3028000-0xf30283ff] pci 0000:00:1f.0: quirk: [io 0x0400-0x047f] claimed by ICH6 ACPI/GPIO/TCO pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by ICH6 GPIO pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0800 (mask 000f) pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 0290 (mask 000f) pci 0000:00:1f.0: ICH7 LPC Generic IO decode 3 PIO at 4700 (mask 000b) pci 0000:00:1f.2: reg 10: [io 0x0000-0x0007] pci 0000:00:1f.2: reg 14: [io 0x0000-0x0003] pci 0000:00:1f.2: reg 18: [io 0x0000-0x0007] pci 0000:00:1f.2: reg 1c: [io 0x0000-0x0003] pci 0000:00:1f.2: reg 20: [io 0xf000-0xf00f] pci 0000:00:1f.2: reg 24: [io 0xfc00-0xfc0f] pci 0000:00:1f.3: reg 10: [mem 0xf3029000-0xf30290ff 64bit] pci 0000:00:1f.3: reg 20: [io 0x0500-0x051f] pci 0000:00:1f.5: reg 10: [io 0xde00-0xde07] pci 0000:00:1f.5: reg 14: [io 0xdf00-0xdf03] pci 0000:00:1f.5: reg 18: [io 0xe000-0xe007] pci 0000:00:1f.5: reg 1c: [io 0xe100-0xe103] pci 0000:00:1f.5: reg 20: [io 0xe200-0xe20f] pci 0000:00:1f.5: reg 24: [io 0xe300-0xe30f] pci 0000:01:00.0: reg 10: [mem 0xe0000000-0xefffffff 64bit pref] pci 0000:01:00.0: reg 18: [mem 0xf1000000-0xf100ffff 64bit] pci 0000:01:00.0: reg 20: [io 0xb000-0xb0ff] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0001ffff pref] pci 0000:01:00.0: supports D1 D2 pci 0000:01:00.1: reg 10: [mem 0xf1010000-0xf1013fff 64bit] pci 0000:01:00.1: supports D1 D2 pci 0000:00:01.0: PCI bridge to [bus 01-01] pci 0000:00:01.0: bridge window [io 0xb000-0xbfff] pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf1ffffff] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref] pci 0000:00:1c.0: PCI bridge to [bus 02-02] pci 0000:00:1c.0: bridge window [io 0x9000-0x9fff] pci 0000:03:00.0: reg 10: [io 0xc000-0xc007] pci 0000:03:00.0: reg 14: [io 0xc100-0xc103] pci 0000:03:00.0: reg 18: [io 0xc200-0xc207] pci 0000:03:00.0: reg 1c: [io 0xc300-0xc303] pci 0000:03:00.0: reg 20: [io 0xc400-0xc40f] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' pci 0000:00:1c.1: PCI bridge to [bus 03-03] pci 0000:00:1c.1: bridge window [io 0xc000-0xcfff] pci 0000:00:1c.1: bridge window [mem 0xf2000000-0xf2ffffff] pci 0000:00:1e.0: PCI bridge to [bus 04-04] (subtractive decode) pci 0000:00:1e.0: bridge window [io 0xa000-0xafff] pci_bus 0000:00: on NUMA node 0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none vgaarb: loaded PCI: Using ACPI for IRQ routing PCI: pci_cache_line_size set to 64 bytes NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default HPET: 4 timers in total, 0 timers will be used for per-cpu timer hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 hpet0: 4 comparators, 64-bit 14.318180 MHz counter Switching to clocksource tsc pnp: PnP ACPI init ACPI: bus type pnp registered ACPI Error (psargs-0359): [TXTB] Namespace lookup failure, AE_NOT_FOUND ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.MEM_._CRS] (Node f6c172b8), AE_NOT_FOUND pnp: PnP ACPI: found 17 devices ACPI: ACPI bus type pnp unregistered PnPBIOS: Disabled system 00:01: [io 0x04d0-0x04d1] has been reserved system 00:01: [io 0x0290-0x029f] has been reserved system 00:01: [io 0x0800-0x0805] has been reserved system 00:01: [io 0x0290-0x0294] has been reserved system 00:01: [io 0x0880-0x088f] has been reserved system 00:0d: [io 0x0400-0x04bf] could not be reserved system 00:0e: [mem 0xd0000000-0xdfffffff] has been reserved pci 0000:00:1c.0: BAR 14: assigned [mem 0x80000000-0x801fffff] pci 0000:00:1c.0: BAR 15: assigned [mem 0x80200000-0x803fffff 64bit pref] pci 0000:00:1c.1: BAR 15: assigned [mem 0x80400000-0x805fffff 64bit pref] pci 0000:01:00.0: BAR 6: assigned [mem 0xf0000000-0xf001ffff pref] pci 0000:00:01.0: PCI bridge to [bus 01-01] pci 0000:00:01.0: bridge window [io 0xb000-0xbfff] pci 0000:00:01.0: bridge window [mem 0xf0000000-0xf1ffffff] pci 0000:00:01.0: bridge window [mem 0xe0000000-0xefffffff 64bit pref] pci 0000:00:1c.0: PCI bridge to [bus 02-02] pci 0000:00:1c.0: bridge window [io 0x9000-0x9fff] pci 0000:00:1c.0: bridge window [mem 0x80000000-0x801fffff] pci 0000:00:1c.0: bridge window [mem 0x80200000-0x803fffff 64bit pref] pci 0000:00:1c.1: PCI bridge to [bus 03-03] pci 0000:00:1c.1: bridge window [io 0xc000-0xcfff] pci 0000:00:1c.1: bridge window [mem 0xf2000000-0xf2ffffff] pci 0000:00:1c.1: bridge window [mem 0x80400000-0x805fffff 64bit pref] pci 0000:00:1e.0: PCI bridge to [bus 04-04] pci 0000:00:1e.0: bridge window [io 0xa000-0xafff] pci 0000:00:1e.0: bridge window [mem disabled] pci 0000:00:1e.0: bridge window [mem pref disabled] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:01.0: setting latency timer to 64 pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:00:1c.0: setting latency timer to 64 pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 pci 0000:00:1c.1: setting latency timer to 64 pci 0000:00:1e.0: setting latency timer to 64 pci_bus 0000:00: resource 0 [io 0x0000-0xffff] pci_bus 0000:00: resource 1 [mem 0x00000000-0xffffffff] pci_bus 0000:01: resource 0 [io 0xb000-0xbfff] pci_bus 0000:01: resource 1 [mem 0xf0000000-0xf1ffffff] pci_bus 0000:01: resource 2 [mem 0xe0000000-0xefffffff 64bit pref] pci_bus 0000:02: resource 0 [io 0x9000-0x9fff] pci_bus 0000:02: resource 1 [mem 0x80000000-0x801fffff] pci_bus 0000:02: resource 2 [mem 0x80200000-0x803fffff 64bit pref] pci_bus 0000:03: resource 0 [io 0xc000-0xcfff] pci_bus 0000:03: resource 1 [mem 0xf2000000-0xf2ffffff] pci_bus 0000:03: resource 2 [mem 0x80400000-0x805fffff 64bit pref] pci_bus 0000:04: resource 0 [io 0xa000-0xafff] pci_bus 0000:04: resource 3 [io 0x0000-0xffff] pci_bus 0000:04: resource 4 [mem 0x00000000-0xffffffff] NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered UDP hash table entries: 512 (order: 2, 16384 bytes) UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) NET: Registered protocol family 1 pci 0000:01:00.0: Boot video device PCI: CLS 32 bytes, default 64 Trying to unpack rootfs image as initramfs... Freeing initrd memory: 5118k freed apm: BIOS not found. audit: initializing netlink socket (disabled) type=2000 audit(1167610067.386:1): initialized highmem bounce pool size: 64 pages HugeTLB registered 4 MB page size, pre-allocated 0 pages VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 1719 alg: No test for stdrng (krng) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) pcieport 0000:00:01.0: setting latency timer to 64 pcieport 0000:00:01.0: irq 24 for MSI/MSI-X pcieport 0000:00:1c.0: setting latency timer to 64 pcieport 0000:00:1c.0: irq 25 for MSI/MSI-X pcieport 0000:00:1c.1: setting latency timer to 64 pcieport 0000:00:1c.1: irq 26 for MSI/MSI-X vesafb: framebuffer at 0xe0000000, mapped to 0xf7c80000, using 1875k, total 16384k vesafb: mode is 800x600x16, linelength=1600, pages=16 vesafb: protected mode interface info at c000:a03e vesafb: pmi: set display start = c00ca0e0, set palette = c00ca19e vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 100x37 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... Linux agpgart interface v0.103 Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A serial 0000:00:03.3: PCI INT B -> GSI 17 (level, low) -> IRQ 17 0000:00:03.3: ttyS2 at I/O 0xd400 (irq = 17) is a 16550A brd: module loaded PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice rtc_cmos 00:04: RTC can wake from S4 rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month, 242 bytes nvram, hpet irqs cpuidle: using governor ladder cpuidle: using governor menu TCP cubic registered Using IPI No-Shortcut mode PM: Checking image partition UUID=baccd61d-3c1e-4d9c-a0ba-e4a80a677833 input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 isapnp: No Plug & Play device found PM: Resume from disk failed. registered taskstats version 1 Magic number: 7:103:101 rtc_cmos 00:04: setting system clock to 2007-01-01 00:07:48 UTC (1167610068) BIOS EDD facility v0.16 2004-Jun-25, 1 devices found Freeing unused kernel memory: 520k freed SCSI subsystem initialized libata version 3.00 loaded. ata_piix 0000:00:1f.2: version 2.13 ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] ata_piix 0000:00:1f.2: setting latency timer to 64 scsi0 : ata_piix scsi1 : ata_piix ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14 ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15 ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19 ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ] ata_piix 0000:00:1f.5: setting latency timer to 64 scsi2 : ata_piix scsi3 : ata_piix ata3: SATA max UDMA/133 cmd 0xde00 ctl 0xdf00 bmdma 0xe200 irq 19 ata4: SATA max UDMA/133 cmd 0xe000 ctl 0xe100 bmdma 0xe208 irq 19 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) ata2.00: SATA link down (SStatus 0 SControl 300) ata2.01: SATA link down (SStatus 0 SControl 300) ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.01: SATA link down (SStatus 0 SControl 300) ata1.00: HPA detected: current 488395055, native 488397168 ata1.00: ATA-8: WDC WD2500AAJS-00B4A0, 01.03A01, max UDMA/133 ata1.00: 488395055 sectors, multi 16: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD2500AAJS-0 01.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 488395055 512-byte logical blocks: (250 GB/232 GiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 < sda5 sda6 > sd 0:0:0:0: [sda] Attached SCSI disk pata_acpi 0000:00:03.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 pata_acpi 0000:00:03.2: setting latency timer to 64 pata_acpi 0000:00:03.2: PCI INT C disabled pata_acpi 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 pata_acpi 0000:03:00.0: setting latency timer to 64 pata_acpi 0000:03:00.0: PCI INT A disabled Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 pata_jmicron 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 pata_jmicron 0000:03:00.0: setting latency timer to 64 scsi4 : pata_jmicron scsi5 : pata_jmicron ata5: PATA max UDMA/100 cmd 0xc000 ctl 0xc100 bmdma 0xc400 irq 17 ata6: PATA max UDMA/100 cmd 0xc200 ctl 0xc300 bmdma 0xc408 irq 17 ata5.00: ATAPI: Optiarc DVD RW AD-5200A, 1.05, max UDMA/66 ata5.00: configured for UDMA/66 scsi 4:0:0:0: CD-ROM Optiarc DVD RW AD-5200A 1.05 PQ: 0 ANSI: 5 ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports PM: Marking nosave pages: 000000000009f000 - 0000000000100000 PM: Basic memory bitmaps created PM: Basic memory bitmaps freed EXT4-fs (sda1): mounted filesystem with ordered data mode Tomoyo security MAC extension available but disabled by default. If you want to enable and use it, ccs-tools package must be installed. udev: starting version 153 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1 ACPI: Power Button [PWRB] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 ACPI: Power Button [PWRF] IT8718 SuperIO detected. parport_pc 00:0a: reported by Plug and Play ACPI parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb tpm_tis 00:0c: 1.2 TPM (device-id 0xB, rev-id 16) ppdev: user-space parallel port driver uhci_hcd: USB Universal Host Controller Interface driver uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1a.0: setting latency timer to 64 uhci_hcd 0000:00:1a.0: UHCI Host Controller uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000d600 usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: UHCI Host Controller usb usb1: Manufacturer: Linux 2.6.33.7-desktop586-2mnb uhci_hcd usb usb1: SerialNumber: 0000:00:1a.0 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 uhci_hcd 0000:00:1a.1: setting latency timer to 64 uhci_hcd 0000:00:1a.1: UHCI Host Controller uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000d700 usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux 2.6.33.7-desktop586-2mnb uhci_hcd usb usb2: SerialNumber: 0000:00:1a.1 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1a.2: setting latency timer to 64 uhci_hcd 0000:00:1a.2: UHCI Host Controller uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1a.2: irq 18, io base 0x0000d800 usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux 2.6.33.7-desktop586-2mnb uhci_hcd usb usb3: SerialNumber: 0000:00:1a.2 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 uhci_hcd 0000:00:1d.0: setting latency timer to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000da00 usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: UHCI Host Controller usb usb4: Manufacturer: Linux 2.6.33.7-desktop586-2mnb uhci_hcd usb usb4: SerialNumber: 0000:00:1d.0 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 uhci_hcd 0000:00:1d.1: setting latency timer to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000db00 usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: UHCI Host Controller usb usb5: Manufacturer: Linux 2.6.33.7-desktop586-2mnb uhci_hcd usb usb5: SerialNumber: 0000:00:1d.1 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 uhci_hcd 0000:00:1d.2: setting latency timer to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 6 uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000dc00 usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb6: Product: UHCI Host Controller usb usb6: Manufacturer: Linux 2.6.33.7-desktop586-2mnb uhci_hcd usb usb6: SerialNumber: 0000:00:1d.2 hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 ehci_hcd 0000:00:1a.7: setting latency timer to 64 ehci_hcd 0000:00:1a.7: EHCI Host Controller ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 7 ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf3025000 ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 usb usb7: New USB device found, idVendor=1d6b, idProduct=0002 usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb7: Product: EHCI Host Controller usb usb7: Manufacturer: Linux 2.6.33.7-desktop586-2mnb ehci_hcd usb usb7: SerialNumber: 0000:00:1a.7 hub 7-0:1.0: USB hub found hub 7-0:1.0: 6 ports detected ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:1d.7: setting latency timer to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 8 ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf3028000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 usb usb8: New USB device found, idVendor=1d6b, idProduct=0002 usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb8: Product: EHCI Host Controller usb usb8: Manufacturer: Linux 2.6.33.7-desktop586-2mnb ehci_hcd usb usb8: SerialNumber: 0000:00:1d.7 hub 8-0:1.0: USB hub found hub 8-0:1.0: 6 ports detected usb 1-1: new low speed USB device using uhci_hcd and address 2 usb 1-1: New USB device found, idVendor=04f3, idProduct=0210 usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0 usb 1-1: Product: PS/2+USB Mouse usbcore: registered new interface driver hiddev input: PS/2+USB Mouse as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1:1.0/input/input3 generic-usb 0003:04F3:0210.0001: input,hidraw0: USB HID v1.11 Mouse [PS/2+USB Mouse] on usb-0000:00:1a.0-1/input0 usbcore: registered new interface driver usbhid usbhid: USB HID core driver device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com Non-volatile memory driver v1.3 loop: module loaded ACPI Error (psargs-0359): [CFGD] Namespace lookup failure, AE_NOT_FOUND ACPI Error (psparse-0537): Method parse/execution failed [\_PR_.CPU0._PCT] (Node f6c17498), AE_NOT_FOUND ACPI Exception: AE_NOT_FOUND, Evaluating _PCT (20091214/processor_perflib-257) [Firmware Bug]: BIOS needs update for CPU frequency support fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel. Disabling lock debugging due to kernel taint EXT4-fs (sda6): mounted filesystem with ordered data mode [fglrx] Maximum main memory to use for locked dma buffers: 1864 MBytes. [fglrx] vendor: 1002 device: 9598 count: 1 [fglrx] ioport: bar 4, base 0xb000, size: 0x100 pci 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 pci 0000:01:00.0: setting latency timer to 64 [fglrx] Kernel PAT support is enabled [fglrx] module loaded - fglrx 8.72.11 [Apr 8 2010] with 1 minors Adding 4088500k swap on /dev/sda5. Priority:-1 extents:1 across:4088500k sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.20 sr 4:0:0:0: Attached scsi CD-ROM sr0 iTCO_vendor_support: vendor-support=0 heci: Intel(R) AMT Management Interface - version 3.2.0.24 heci: Copyright (c) 2003 - 2007 Intel Corporation. heci 0000:00:03.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 heci 0000:00:03.0: setting latency timer to 64 e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2 e1000e: Copyright (c) 1999 - 2009 Intel Corporation. sd 0:0:0:0: Attached scsi generic sg0 type 0 sr 4:0:0:0: Attached scsi generic sg1 type 5 fglrx_pci 0000:01:00.0: irq 27 for MSI/MSI-X [fglrx] Firegl kernel thread PID: 1182 [fglrx] IRQ 27 Enabled iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05 iTCO_wdt: Found a ICH9DO TCO device (Version=2, TCOBASE=0x0460) iTCO_wdt: initialized. heartbeat=30 sec (nowayout=1) [fglrx] Gart USWC size:620 M. [fglrx] Gart cacheable size:244 M. [fglrx] Reserved FB block: Shared offset:0, size:1000000 [fglrx] Reserved FB block: Unshared offset:fe0d000, size:1f3000 [fglrx] Reserved FB block: Unshared offset:1fffc000, size:4000 heci: init hw failure. heci 0000:00:03.0: PCI INT A disabled heci: heci driver initialization failed. i801_smbus 0000:00:1f.3: PCI INT C -> GSI 18 (level, low) -> IRQ 18 e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 e1000e 0000:00:19.0: setting latency timer to 64 e1000e 0000:00:19.0: irq 28 for MSI/MSI-X 0000:00:19.0: 0000:00:19.0: The NVM Checksum Is Not Valid e1000e 0000:00:19.0: PCI INT A disabled e1000e: probe of 0000:00:19.0 failed with error -5 HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 HDA Intel 0000:00:1b.0: irq 28 for MSI/MSI-X HDA Intel 0000:00:1b.0: setting latency timer to 64 HDA Intel 0000:01:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 HDA Intel 0000:01:00.1: irq 29 for MSI/MSI-X HDA Intel 0000:01:00.1: setting latency timer to 64 hda-intel: IRQ timing workaround is activated for card #1. Suggest a bigger bdl_pos_adj. NET: Registered protocol family 10 lo: Disabled Privacy Extensions fuse init (API version 7.13) ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (16384 buckets, 65536 max) CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or sysctl net.netfilter.nf_conntrack_acct=1 to enable it. NF_TPROXY: Transparent proxy support initialized, version 4.1.0 NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. ip_set version 4 loaded ctnetlink v0.93: registering with nfnetlink. ClusterIP Version 0.8 loaded successfully xt_time: kernel timezone is +0300 u32 classifier Actions configured netfilter PSD loaded - (c) astaro AG IFWLOG: register target end_request: I/O error, dev fd0, sector 0 end_request: I/O error, dev fd0, sector 0 usb 7-6: new high speed USB device using ehci_hcd and address 3 usb 7-6: New USB device found, idVendor=8564, idProduct=1000 usb 7-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 7-6: Product: Mass Storage Device usb 7-6: Manufacturer: JetFlash usb 7-6: SerialNumber: 3YR688TV Initializing USB Mass Storage driver... scsi6 : usb-storage 7-6:1.0 usbcore: registered new interface driver usb-storage USB Mass Storage support registered. scsi 6:0:0:0: Direct-Access JetFlash Transcend 16GB 8.01 PQ: 0 ANSI: 2 sd 6:0:0:0: Attached scsi generic sg2 type 0 scsi 6:0:0:1: CD-ROM Generic AutoRun Disk 8.00 PQ: 0 ANSI: 2 sd 6:0:0:0: [sdb] 31352820 512-byte logical blocks: (16.0 GB/14.9 GiB) sd 6:0:0:0: [sdb] Write Protect is off sd 6:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 6:0:0:0: [sdb] Assuming drive cache: write through sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 tray sr 6:0:0:1: Attached scsi CD-ROM sr1 sr 6:0:0:1: Attached scsi generic sg3 type 5 sd 6:0:0:0: [sdb] Assuming drive cache: write through sdb: sdb1 sd 6:0:0:0: [sdb] Assuming drive cache: write through sd 6:0:0:0: [sdb] Attached SCSI removable disk ISO 9660 Extensions: Microsoft Joliet Level 3 ISOFS: changing to secondary root usb 7-6: USB disconnect, address 3 sd 6:0:0:0: [sdb] Unhandled error code sd 6:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK sd 6:0:0:0: [sdb] CDB: Write(10): 2a 00 00 5f fe 27 00 00 18 00 end_request: I/O error, dev sdb, sector 6290983 Buffer I/O error on device sdb1, logical block 786365 lost page write due to I/O error on sdb1 Buffer I/O error on device sdb1, logical block 786366 lost page write due to I/O error on sdb1 Buffer I/O error on device sdb1, logical block 786367 lost page write due to I/O error on sdb1 sd 6:0:0:0: [sdb] Unhandled error code sd 6:0:0:0: [sdb] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK sd 6:0:0:0: [sdb] CDB: Write(10): 2a 00 00 60 cb bf 00 00 08 00 end_request: I/O error, dev sdb, sector 6343615 Buffer I/O error on device sdb1, logical block 792944 lost page write due to I/O error on sdb1 usb 8-2: new high speed USB device using ehci_hcd and address 2 usb 8-2: New USB device found, idVendor=8564, idProduct=1000 usb 8-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 8-2: Product: Mass Storage Device usb 8-2: Manufacturer: JetFlash usb 8-2: SerialNumber: 3YR688TV scsi7 : usb-storage 8-2:1.0 scsi 7:0:0:0: Direct-Access JetFlash Transcend 16GB 8.01 PQ: 0 ANSI: 2 sd 7:0:0:0: Attached scsi generic sg2 type 0 scsi 7:0:0:1: CD-ROM Generic AutoRun Disk 8.00 PQ: 0 ANSI: 2 sr1: scsi3-mmc drive: 52x/52x cd/rw xa/form2 tray sr 7:0:0:1: Attached scsi CD-ROM sr1 sr 7:0:0:1: Attached scsi generic sg3 type 5 sd 7:0:0:0: [sdb] 31352820 512-byte logical blocks: (16.0 GB/14.9 GiB) sd 7:0:0:0: [sdb] Write Protect is off sd 7:0:0:0: [sdb] Mode Sense: 03 00 00 00 sd 7:0:0:0: [sdb] Assuming drive cache: write through sd 7:0:0:0: [sdb] Assuming drive cache: write through sdb: sdb1 sd 7:0:0:0: [sdb] Assuming drive cache: write through sd 7:0:0:0: [sdb] Attached SCSI removable disk ISO 9660 Extensions: Microsoft Joliet Level 3 ISOFS: changing to secondary root

13 октября 2011, 20:03 Школа8 Записей: 862	Второго лога на половину нет

13 октября 2011, 21:22 linux user Записей: 15	К сожалению, это баг сайта, вероятно. Текст только до середины выкладывается. Пробовал с разных браузеров. Выхода не вижу, кроме как залить в текстовых документы на сторонний ресурс. Ссылки прилагаю. http://files.mail.ru/9VJ2A1 - есть интернет на котором. http://files.mail.ru/PZMYE9 - на котором инернета нет.

13 октября 2011, 22:45 Школа8 Записей: 862	так... А на той и на другой машине если эти команды ввести ifconfig -a >fip.txt ip a >>fip.txt можно файлы fip.txt на форум ?

14 октября 2011, 17:38 linux user Записей: 15	Спасибо всем. Тему можно считать закрытой, устал возиться, поставил на 2 пк отдельно сетевушки, встроенные выключил - все завелось и работает ок. Единственное, что спрошу (хоть и не по теме) - не могу зайти ни с одного компьютера на данный ресурс, хотя пинг идет. Выхода через прокси нет, не пойму в чем причина...

Войдите чтобы ответить на тему