не работает WiFi в alt linux юниор

Сообщений: 35, участников: 5

Ответить

Список: 1-25 из 35

18 января 2011, 20:27 Иван Зибарев Записей: 9	Иван Зибарев писал(а): Наверно уже такая проблема обсуждалась на форуме, но я не нашел. Вобщем неработает беспроводная сеть, сетевую карту вроде видит но кнопка настройки для беспроводной сети недоступна. ip выставлен вручную, под Windows все нормально работало. Есть ли какоето проверенное решение?

18 января 2011, 20:31 Julia Dronova (administrator) Записей: 3144	какая карта? покажите вывод (можно сразу из-под рута) lspci iwconfig Альт 4 или 5?

18 января 2011, 20:34 Иван Зибарев Записей: 9	Компьютер на работе. :)) Завтра напишу.

18 января 2011, 20:40 Иван Зибарев Записей: 9	4

19 января 2011, 10:25 Иван Зибарев Записей: 9	[root@dr ~]# lspci 00:00.0 Host bridge: VIA Technologies, Inc. P4M266 Host Bridge 00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP] 00:0b.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller (rev 20) 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 80) 00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50) 00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 74) 01:00.0 VGA compatible controller: S3 Inc. VT8375 [ProSavage8 KM266/KL266] [root@dr ~]# iwconfig bash: iwconfig: command not found Тоесть вторая команда не выполнилась.

19 января 2011, 14:08 Viktor Записей: 1327	ifconfig показывает беспроводной интерфейс (типа wlan0)?

19 января 2011, 14:33 Julia Dronova (administrator) Записей: 3144	Да, тогда хотя бы /sbin/ifconfig -a

19 января 2011, 15:22 Julia Dronova (administrator) Записей: 3144	Добавлено: полюбому нужно будет поставить пакет wireless-tools. Я так поняла, что интернета на машине нет, тогда для Альт4 это будет ВОТ ЭТОТ пакет. Скачать, перенести на машину с линь, из-под рута сделать rpm -ihv <пакет>.rpm затем снова смотреть iwconfig

19 января 2011, 17:35 Иван Зибарев Записей: 9	[root@dr ~]# /sbin/ifconfig -a eth0 Link encap:Ethernet HWaddr 00:0D:87:55:55:F5 inet addr:192.168.0.5 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:177 Base address:0xd800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1858 errors:0 dropped:0 overruns:0 frame:0 TX packets:1858 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:215229 (210.1 KiB) TX bytes:215229 (210.1 KiB) eth0 - должен быть беспроводной (или они вместе должны работать с ним?) ip на нем поставил вручную, в консоле через ping связь есть(Это чтото значит?) На установку Вашего пакета выдал следующее: [root@dr 22]# rpm -ihv wireless-tools-28-alt7.1.i586.rpm предупреждение: Ожидаемый размер: 62432 = lead(96)+sigs(241)+pad(7)+data(62088) предупреждение: Фактический размер: 1460 [root@dr 22]# Посмотрел по менеджеру пакетов, этот пакет вроде как учтановлен. Может ли быть такое что его какт надо вручную запустить? Или что еще для беспроводной связи возможно вручную запускается? Потому что вроде сама сетевуха определяется нонрмально.

19 января 2011, 17:43 Julia Dronova (administrator) Записей: 3144	Если пакет wireles--tools установлен, дайте уже вывод из-под рута iwconfig Ничего запускать не надо, если пакет установлен, то команда в системе присутствует. Если нет -- то пакет не установлен. На всякий случай почитайте сначала основы работы с Синаптиком: управление пакетами, Synaptic, Настройка системы для обновления по сети зы -- при копи-пасте консольных выводов применяйте форматирование "Преформатированный" из ниспадающего списка. Выделить текст-- применить форматирование. Иначе нечитаемая каша. См. ФАК, вопрос 7.

20 января 2011, 10:57 Иван Зибарев Записей: 9	Я же уже делал, или когда в консоле вводишь су, пароль, команду - она не из под рута выполняется?

20 января 2011, 11:08 Иван Зибарев Записей: 9	о, вошел через консоль, iwconfig выдал no wireless extension Видимо с драйверами надо чтото делать?

25 января 2011, 15:35 Иван Зибарев Записей: 9	Вобщем порылся в интернете, нашел подходящую версию linux, поставил - все отлично и резво работает.

25 января 2011, 15:56 Julia Dronova (administrator) Записей: 3144	Иван Зибарев писал(а): Вобщем порылся в интернете, нашел подходящую версию linux, поставил - все отлично и резво работает. Иван, какую именно? Я всегда про это спрашиваю не из любопытства, а потому, что форум читает множество народа с аналогичными проблемами, не устаю это повторять.

26 января 2011, 10:59 Иван Зибарев Записей: 9	Lupurus-510. Работаю 3й день на ней никаких проблем пока небыло, документы word, excel открываются без глюков. практически все на русском языке, во всех программах объяснения что к чему, как и зачем. Через встроенный менеждер разделов успешно отформатировал флешку с которой в вин ХР и юниоре почемуто ниче сделать не получалось

15 декабря 2011, 18:53 Александр Карпов Записей: 25	Есть беспроводная сетевая карта нужно подключить и настроить ее в линукс юниор 5,02 Шифрование wpa-psk. Все настройки сетевой карты подтягивает из сети по dhcp Вывод команды ifconfig <dl> eth0 Link encap:Ethernet HWaddr 00:1D:92:B8:3A:49 inet addr:10.22.0.48 Bcast:10.22.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:12942 errors:0 dropped:0 overruns:0 frame:0 TX packets:3163 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2748127 (2.6 MiB) TX bytes:361323 (352.8 KiB) Interrupt:26 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:748 errors:0 dropped:0 overruns:0 frame:0 TX packets:748 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:89915 (87.8 KiB) TX bytes:89915 (87.8 KiB) pan0 Link encap:Ethernet HWaddr EE:14:50:8F:AF:61 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vboxnet0 Link encap:Ethernet HWaddr 0A:00:27:00:00:00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) wlan0 Link encap:Ethernet HWaddr 00:E0:4C:6D:1D:B0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Вывод команды grep -i wireless невозможен так как сеанс рута зависает вывод команда не дает вывода в центре управления системой в графическом интерфейсе настройки для беспроводной сети отсутвуют Куда идти лаьше? </dl>

15 декабря 2011, 18:55 Александр Карпов Записей: 25	и еще вывод <dl> root@kab24-01 ~]# rpm -qa \| grep NetworkManager NetworkManager-pptp-gnome-0.7.2-alt1.M51.1 NetworkManager-openvpn-0.7.2-alt1.M51.1 NetworkManager-openvpn-gnome-0.7.2-alt1.M51.1 NetworkManager-gnome-0.7.2-alt1.M51.1 NetworkManager-vpnc-0.7.2-alt1.M51.1 NetworkManager-pptp-0.7.2-alt1.M51.1 NetworkManager-0.7.2-alt2.M50P.1 NetworkManager-glib-0.7.2-alt2.M50P.1 [root@kab24-01 ~]# </dl>

15 декабря 2011, 20:31 Julia Dronova (administrator) Записей: 3144	Что зв карта? Название и модель. > Вывод команды grep -i wireless невозможен так как сеанс рута зависает вот это оч странное что-то, можно подробности? что-то ещё зависает? ЗЫ -- да, и вывод dmesg в студию

16 декабря 2011, 15:57 Александр Карпов Записей: 25	Катра беспроводная G- sky Вот такая http://www.instructables.com/answers/How-can-I-...

16 декабря 2011, 16:19 Александр Карпов Записей: 25	Больше ничего не зависает после ввода этой команды uxterm молчит больше никакие команды не ввoдятся. В прикрепленном файле вывод команды

16 декабря 2011, 16:25 Александр Карпов Записей: 25	Александр Карпов писал(а): Больше ничего не зависает после ввода этой команды uxterm молчит больше никакие команды не ввoдятся. В прикрепленном файле вывод команды Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 002: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter

16 декабря 2011, 16:29 Александр Карпов Записей: 25	Александр Карпов писал(а): Александр Карпов писал(а): Больше ничего не зависает после ввода этой команды uxterm молчит больше никакие команды не ввoдятся. В прикрепленном файле вывод команды Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 002: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter Что файл не прикрепляется и полностью в пост на форуме не вставляется

16 декабря 2011, 16:30 Александр Карпов Записей: 25	И еще есть драйвера под линукс на эту карту на диске производителя

16 декабря 2011, 16:31 Julia Dronova (administrator) Записей: 3144	Александр Карпов писал(а): Что файл не прикрепляется и полностью в пост на форуме не вставляется Выложите, пож-та, на http://pastebin.ru/ У пользователей нет прав для прикрепления файлов, т.к. особо беспечные пользователи всеми любимой Виндовс могут выложить варез или программу с вирусами, а отвечать потом администрации. Надо указать это в факе, кажется я там про это не писала. > И еще есть драйвера под линукс на эту карту на диске производителя Можете показать содержимое диска? ещё лучше заархивировать каталоги для линукс и тоже выложить куда-нить на файлообменник. Только не в rar! Вы пытались эти драйверы поставить? Там обычно должен идти файл readme, в котором как правило написано, под какие дистрибутивы работают драйверы, и как их ставить.

16 декабря 2011, 16:43 Александр Карпов Записей: 25	Александр Карпов писал(а): Александр Карпов писал(а): Больше ничего не зависает после ввода этой команды uxterm молчит больше никакие команды не ввoдятся. В прикрепленном файле вывод команды Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 002: ID 0bda:8187 Realtek Semiconductor Corp. RTL8187 Wireless Adapter Что файл не прикрепляется и полностью в пост на форуме не вставляется [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.32-std-def-alt20.M50P.1 (builder@apiary.armor.altlinux.org) (gcc version 4.3.2 20081105 (ALT Linux 4.3.2-alt13) (GCC) ) #1 SMP Mon Sep 6 11:11:43 UTC 2010 [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] NSC Geode by NSC [ 0.000000] Cyrix CyrixInstead [ 0.000000] Centaur CentaurHauls [ 0.000000] Transmeta GenuineTMx86 [ 0.000000] Transmeta TransmetaCPU [ 0.000000] UMC UMC UMC UMC [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000001f7a0000 (usable) [ 0.000000] BIOS-e820: 000000001f7a0000 - 000000001f7ae000 (ACPI data) [ 0.000000] BIOS-e820: 000000001f7ae000 - 000000001f7f0000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000001f7f0000 - 000000001f7fe000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] DMI present. [ 0.000000] AMI BIOS detected: BIOS may corrupt low RAM, working around it. [ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved) [ 0.000000] last_pfn = 0x1f7a0 max_arch_pfn = 0x100000 [ 0.000000] MTRR default type: uncachable [ 0.000000] MTRR fixed ranges enabled: [ 0.000000] 00000-9FFFF write-back [ 0.000000] A0000-DFFFF uncachable [ 0.000000] E0000-EFFFF write-through [ 0.000000] F0000-FFFFF write-protect [ 0.000000] MTRR variable ranges enabled: [ 0.000000] 0 base 000000000 mask FE0000000 write-back [ 0.000000] 1 base 01F800000 mask FFF800000 uncachable [ 0.000000] 2 disabled [ 0.000000] 3 disabled [ 0.000000] 4 disabled [ 0.000000] 5 disabled [ 0.000000] 6 disabled [ 0.000000] 7 disabled [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] Scanning 0 areas for low memory corruption [ 0.000000] modified physical RAM map: [ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved) [ 0.000000] modified: 0000000000010000 - 000000000009fc00 (usable) [ 0.000000] modified: 000000000009fc00 - 00000000000a0000 (reserved) [ 0.000000] modified: 00000000000e0000 - 0000000000100000 (reserved) [ 0.000000] modified: 0000000000100000 - 000000001f7a0000 (usable) [ 0.000000] modified: 000000001f7a0000 - 000000001f7ae000 (ACPI data) [ 0.000000] modified: 000000001f7ae000 - 000000001f7f0000 (ACPI NVS) [ 0.000000] modified: 000000001f7f0000 - 000000001f7fe000 (reserved) [ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] modified: 00000000fff80000 - 0000000100000000 (reserved) [ 0.000000] initial memory mapped : 0 - 01800000 [ 0.000000] init_memory_mapping: 0000000000000000-000000001f7a0000 [ 0.000000] 0000000000 - 0000400000 page 4k [ 0.000000] 0000400000 - 001f400000 page 2M [ 0.000000] 001f400000 - 001f7a0000 page 4k [ 0.000000] kernel direct mapping tables up to 1f7a0000 @ 10000-16000 [ 0.000000] RAMDISK: 00e72000 - 00eff041 [ 0.000000] ACPI: RSDP 000f97d0 00014 (v00 ACPIAM) [ 0.000000] ACPI: RSDT 1f7a0000 00034 (v01 010708 RSDT1033 20080107 MSFT 00000097) [ 0.000000] ACPI: FACP 1f7a0200 00084 (v01 010708 FACP1033 20080107 MSFT 00000097) [ 0.000000] ACPI: DSDT 1f7a0440 050F6 (v01 0AAAA 0AAAA000 00000000 INTL 20051117) [ 0.000000] ACPI: FACS 1f7ae000 00040 [ 0.000000] ACPI: APIC 1f7a0390 0006C (v01 010708 APIC1033 20080107 MSFT 00000097) [ 0.000000] ACPI: MCFG 1f7a0400 0003C (v01 010708 OEMMCFG 20080107 MSFT 00000097) [ 0.000000] ACPI: OEMB 1f7ae040 00071 (v01 010708 OEMB1033 20080107 MSFT 00000097) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 503MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 1f7a0000 [ 0.000000] low ram: 0 - 1f7a0000 [ 0.000000] node 0 low ram: 00000000 - 1f7a0000 [ 0.000000] node 0 bootmap 00012000 - 00015ef4 [ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 001f7a0000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] [ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] [ 0.000000] #3 [0001000000 - 00015c3f84] TEXT DATA BSS ==> [0001000000 - 00015c3f84] [ 0.000000] #4 [0000e72000 - 0000eff041] RAMDISK ==> [0000e72000 - 0000eff041] [ 0.000000] #5 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] [ 0.000000] #6 [00015c4000 - 00015ca15f] BRK ==> [00015c4000 - 00015ca15f] [ 0.000000] #7 [0000010000 - 0000012000] PGTABLE ==> [0000010000 - 0000012000] [ 0.000000] #8 [0000012000 - 0000016000] BOOTMAP ==> [0000012000 - 0000016000] [ 0.000000] found SMP MP-table at [c00ff780] ff780 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000010 -> 0x00001000 [ 0.000000] Normal 0x00001000 -> 0x0001f7a0 [ 0.000000] HighMem 0x0001f7a0 -> 0x0001f7a0 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[2] active PFN ranges [ 0.000000] 0: 0x00000010 -> 0x0000009f [ 0.000000] 0: 0x00000100 -> 0x0001f7a0 [ 0.000000] On node 0 totalpages: 128815 [ 0.000000] free_area_init_node: node 0, pgdat c14965c0, node_mem_map c15cc200 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3951 pages, LIFO batch:0 [ 0.000000] Normal zone: 976 pages used for memmap [ 0.000000] Normal zone: 123856 pages, LIFO batch:31 [ 0.000000] Using APIC driver default [ 0.000000] ACPI: PM-Timer IO Port: 0x808 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled) [ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] SMP: Allowing 4 CPUs, 3 hotplug CPUs [ 0.000000] nr_irqs_gsi: 24 [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at 1f7fe000 (gap: 1f7fe000:df602000) [ 0.000000] Booting paravirtualized kernel on bare hardware [ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:4 nr_node_ids:1 [ 0.000000] PERCPU: Embedded 14 pages/cpu @c1c00000 s33016 r0 d24328 u1048576 [ 0.000000] pcpu-alloc: s33016 r0 d24328 u1048576 alloc=14194304 [ 0.000000] pcpu-alloc: [0] 0 1 2 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 127807 [ 0.000000] Kernel command line: auto BOOT_IMAGE=ALTLinux ro root=UUID=1e95aaf2-8a22-4268-adf3-4d619b149c22 resume=/dev/disk/by-uuid/8e33da95-7893-4861-9ec4-1254cdf6763a panic=30 splash=silent quiet=1 [ 0.000000] bootsplash: silent mode. [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] allocated 2578240 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Initializing HighMem for node 0 (00000000:00000000) [ 0.000000] Memory: 500972k/515712k available (3171k kernel code, 13716k reserved, 1563k data, 540k init, 0k highmem) [ 0.000000] virtual kernel memory layout: [ 0.000000] fixmap : 0xffd55000 - 0xfffff000 (2728 kB) [ 0.000000] pkmap : 0xff400000 - 0xff800000 (4096 kB) [ 0.000000] vmalloc : 0xdffa0000 - 0xff3fe000 ( 500 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdf7a0000 ( 503 MB) [ 0.000000] .init : 0xc14a0000 - 0xc1527000 ( 540 kB) [ 0.000000] .data : 0xc1318d4c - 0xc149fc08 (1563 kB) [ 0.000000] .text : 0xc1000000 - 0xc1318d4c (3171 kB) [ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:2304 nr_irqs:440 [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 2016.273 MHz processor. [ 0.004005] Calibrating delay loop (skipped), value calculated using timer frequency.. 4032.54 BogoMIPS (lpj=8065092) [ 0.004045] Security Framework initialized [ 0.004050] SELinux: Disabled at boot. [ 0.004068] Mount-cache hash table entries: 512 [ 0.004188] Initializing cgroup subsys ns [ 0.004192] Initializing cgroup subsys cpuacct [ 0.004197] Initializing cgroup subsys memory [ 0.004205] Initializing cgroup subsys devices [ 0.004207] Initializing cgroup subsys freezer [ 0.004210] Initializing cgroup subsys net_cls [ 0.004236] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.004239] CPU: L2 cache: 512K [ 0.004243] mce: CPU supports 6 MCE banks [ 0.004252] CPU0: Thermal monitoring enabled (TM2) [ 0.004256] using mwait in idle threads. [ 0.004261] Performance Events: Core2 events, Intel PMU driver. [ 0.004278] ... version: 2 [ 0.004280] ... bit width: 40 [ 0.004281] ... generic registers: 2 [ 0.004283] ... value mask: 000000ffffffffff [ 0.004285] ... max period: 000000007fffffff [ 0.004287] ... fixed-purpose events: 3 [ 0.004289] ... event mask: 0000000700000003 [ 0.004295] Checking 'hlt' instruction... OK. [ 0.020640] SMP alternatives: switching to UP code [ 0.025891] ACPI: Core revision 20090903 [ 0.036075] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.036386] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.077032] CPU0: Intel(R) Celeron(R) CPU 440 @ 2.00GHz stepping 01 [ 0.080001] Brought up 1 CPUs [ 0.080001] Total of 1 processors activated (4032.54 BogoMIPS). [ 0.080001] CPU0 attaching NULL sched-domain. [ 0.080001] regulator: core version 0.5 [ 0.080001] NET: Registered protocol family 16 [ 0.080001] EISA bus registered [ 0.080001] ACPI: bus type pci registered [ 0.080001] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 [ 0.080001] PCI: Not using MMCONFIG. [ 0.080001] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=3 [ 0.080001] PCI: Using configuration type 1 for base access [ 0.080001] bio: create slab <bio-0> at 0 [ 0.080430] ACPI: EC: Look up EC in DSDT [ 0.083302] ACPI: Executed 1 blocks of module-level executable AML code [ 0.087930] ACPI: Interpreter enabled [ 0.087939] ACPI: (supports S0 S1 S4 S5) [ 0.087961] ACPI: Using IOAPIC for interrupt routing [ 0.088034] PCI: MCFG configuration 0: base f0000000 segment 0 buses 0 - 255 [ 0.099883] PCI: MCFG area at f0000000 reserved in ACPI motherboard resources [ 0.099887] PCI: updated MCFG configuration 0: base f0000000 segment 0 buses 0 - 63 [ 0.099889] PCI: Using MMCONFIG for extended config space [ 0.111719] ACPI Warning: Incorrect checksum in table [OEMB] - F6, should be E7 (20090903/tbutils-314) [ 0.111824] ACPI: No dock devices found. [ 0.112174] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.112324] pci 0000:00:02.0: reg 10 32bit mmio: [0xcfe80000-0xcfefffff] [ 0.112329] pci 0000:00:02.0: reg 14 io port: [0xec00-0xec07] [ 0.112334] pci 0000:00:02.0: reg 18 32bit mmio pref: [0xe0000000-0xefffffff] [ 0.112339] pci 0000:00:02.0: reg 1c 32bit mmio: [0xcfe40000-0xcfe7ffff] [ 0.112416] pci 0000:00:1b.0: reg 10 64bit mmio: [0xcfe3c000-0xcfe3ffff] [ 0.112459] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 0.112463] pci 0000:00:1b.0: PME# disabled [ 0.112526] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.112530] pci 0000:00:1c.0: PME# disabled [ 0.112594] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 0.112598] pci 0000:00:1c.1: PME# disabled [ 0.112647] pci 0000:00:1d.0: reg 20 io port: [0xe880-0xe89f] [ 0.112696] pci 0000:00:1d.1: reg 20 io port: [0xe800-0xe81f] [ 0.112744] pci 0000:00:1d.2: reg 20 io port: [0xe480-0xe49f] [ 0.112792] pci 0000:00:1d.3: reg 20 io port: [0xe400-0xe41f] [ 0.112845] pci 0000:00:1d.7: reg 10 32bit mmio: [0xcfe3bc00-0xcfe3bfff] [ 0.112896] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.112900] pci 0000:00:1d.7: PME# disabled [ 0.113027] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000 [ 0.113033] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO [ 0.113037] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO [ 0.113041] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 1 PIO at 0a00 (mask 00ff) [ 0.113045] pci 0000:00:1f.0: ICH7 LPC Generic IO decode 2 PIO at 4700 (mask 00ff) [ 0.113087] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07] [ 0.113094] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03] [ 0.113101] pci 0000:00:1f.1: reg 18 io port: [0x8f0-0x8f7] [ 0.113107] pci 0000:00:1f.1: reg 1c io port: [0x8f8-0x8fb] [ 0.113114] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf] [ 0.113154] pci 0000:00:1f.2: reg 10 io port: [0xe080-0xe087] [ 0.113160] pci 0000:00:1f.2: reg 14 io port: [0xe000-0xe003] [ 0.113166] pci 0000:00:1f.2: reg 18 io port: [0xdc00-0xdc07] [ 0.113172] pci 0000:00:1f.2: reg 1c io port: [0xd880-0xd883] [ 0.113178] pci 0000:00:1f.2: reg 20 io port: [0xd800-0xd80f] [ 0.113202] pci 0000:00:1f.2: PME# supported from D3hot [ 0.113206] pci 0000:00:1f.2: PME# disabled [ 0.113251] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f] [ 0.113373] pci 0000:02:00.0: reg 10 io port: [0xc800-0xc8ff] [ 0.113396] pci 0000:02:00.0: reg 18 64bit mmio: [0xcfcff000-0xcfcfffff] [ 0.113419] pci 0000:02:00.0: reg 30 32bit mmio pref: [0xcfcc0000-0xcfcdffff] [ 0.113466] pci 0000:02:00.0: supports D1 D2 [ 0.113469] pci 0000:02:00.0: PME# supported from D1 D2 D3hot D3cold [ 0.113474] pci 0000:02:00.0: PME# disabled [ 0.113513] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force' [ 0.113587] pci 0000:00:1c.1: bridge io port: [0xc000-0xcfff] [ 0.113591] pci 0000:00:1c.1: bridge 32bit mmio: [0xcfc00000-0xcfcfffff] [ 0.113641] pci 0000:00:1e.0: transparent bridge [ 0.113663] pci_bus 0000:00: on NUMA node 0 [ 0.113672] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.113839] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 0.113976] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT] [ 0.114038] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT] [ 0.118308] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11 12 14 15) [ 0.118416] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11 12 14 15) [ 0.118520] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) [ 0.118622] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11 12 14 15) [ 0.118724] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) 0, disabled. [ 0.118826] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) 0, disabled. [ 0.118930] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) 0, disabled. [ 0.119034] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 11 12 14 15) [ 0.119272] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none [ 0.119280] vgaarb: loaded [ 0.119624] PCI: Using ACPI for IRQ routing [ 0.119846] NetLabel: Initializing [ 0.119849] NetLabel: domain hash size = 128 [ 0.119850] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.119862] NetLabel: unlabeled traffic allowed by default [ 0.119982] hpet clockevent registered [ 0.119985] HPET: 3 timers in total, 0 timers will be used for per-cpu timer [ 0.120016] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 [ 0.120021] hpet0: 3 comparators, 64-bit 14.318180 MHz counter [ 0.124090] Switching to clocksource tsc [ 0.125393] pnp: PnP ACPI init [ 0.125419] ACPI: bus type pnp registered [ 0.131287] pnp: PnP ACPI: found 19 devices [ 0.131291] ACPI: ACPI bus type pnp unregistered [ 0.131295] PnPBIOS: Disabled by ACPI PNP [ 0.131310] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved [ 0.131322] system 00:0c: ioport range 0xa00-0xadf has been reserved [ 0.131325] system 00:0c: ioport range 0xae0-0xaef has been reserved [ 0.131331] system 00:0d: ioport range 0x4d0-0x4d1 has been reserved [ 0.131334] system 00:0d: ioport range 0x800-0x87f has been reserved [ 0.131337] system 00:0d: ioport range 0x480-0x4bf has been reserved [ 0.131340] system 00:0d: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 0.131343] system 00:0d: iomem range 0xfed20000-0xfed3ffff has been reserved [ 0.131346] system 00:0d: iomem range 0xfed45000-0xfed89fff has been reserved [ 0.131353] system 00:0f: iomem range 0xffc00000-0xfff7ffff has been reserved [ 0.131362] system 00:10: iomem range 0xfec00000-0xfec00fff could not be reserved [ 0.131365] system 00:10: iomem range 0xfee00000-0xfee00fff has been reserved [ 0.131370] system 00:11: iomem range 0xf0000000-0xf3ffffff has been reserved [ 0.131375] system 00:12: iomem range 0x0-0x9ffff could not be reserved [ 0.131378] system 00:12: iomem range 0xc0000-0xcffff could not be reserved [ 0.131381] system 00:12: iomem range 0xe0000-0xfffff could not be reserved [ 0.131384] system 00:12: iomem range 0x100000-0x1f7fffff could not be reserved [ 0.166459] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:01 [ 0.166464] pci 0000:00:1c.0: IO window: 0x1000-0x1fff [ 0.166469] pci 0000:00:1c.0: MEM window: 0x20000000-0x201fffff [ 0.166473] pci 0000:00:1c.0: PREFETCH window: 0x00000020200000-0x000000203fffff [ 0.166480] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02 [ 0.166483] pci 0000:00:1c.1: IO window: 0xc000-0xcfff [ 0.166488] pci 0000:00:1c.1: MEM window: 0xcfc00000-0xcfcfffff [ 0.166493] pci 0000:00:1c.1: PREFETCH window: 0x00000020400000-0x000000205fffff [ 0.166499] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:03 [ 0.166501] pci 0000:00:1e.0: IO window: disabled [ 0.166505] pci 0000:00:1e.0: MEM window: disabled [ 0.166509] pci 0000:00:1e.0: PREFETCH window: disabled [ 0.166523] pci 0000:00:1c.0: enabling device (0104 -> 0107) [ 0.166530] alloc irq_desc for 16 on node -1 [ 0.166532] alloc kstat_irqs on node -1 [ 0.166538] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.166543] pci 0000:00:1c.0: setting latency timer to 64 [ 0.166551] alloc irq_desc for 17 on node -1 [ 0.166553] alloc kstat_irqs on node -1 [ 0.166556] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [ 0.166560] pci 0000:00:1c.1: setting latency timer to 64 [ 0.166567] pci 0000:00:1e.0: setting latency timer to 64 [ 0.166572] pci_bus 0000:00: resource 0 io: [0x00-0xffff] [ 0.166575] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] [ 0.166578] pci_bus 0000:01: resource 0 io: [0x1000-0x1fff] [ 0.166580] pci_bus 0000:01: resource 1 mem: [0x20000000-0x201fffff] [ 0.166583] pci_bus 0000:01: resource 2 pref mem [0x20200000-0x203fffff] [ 0.166586] pci_bus 0000:02: resource 0 io: [0xc000-0xcfff] [ 0.166588] pci_bus 0000:02: resource 1 mem: [0xcfc00000-0xcfcfffff] [ 0.166591] pci_bus 0000:02: resource 2 pref mem [0x20400000-0x205fffff] [ 0.166594] pci_bus 0000:03: resource 3 io: [0x00-0xffff] [ 0.166596] pci_bus 0000:03: resource 4 mem: [0x000000-0xffffffff] [ 0.166652] NET: Registered protocol family 2 [ 0.166750] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.167012] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 0.167066] TCP bind hash table entries: 16384 (order: 5, 131072 bytes) [ 0.167121] TCP: Hash tables configured (established 16384 bind 16384) [ 0.167124] TCP reno registered [ 0.167220] NET: Registered protocol family 1 [ 0.167239] pci 0000:00:02.0: Boot video device [ 0.167372] Trying to unpack rootfs image as initramfs... [ 0.184370] Freeing initrd memory: 564k freed [ 0.185165] Machine check injector initialized [ 0.185303] Scanning for low memory corruption every 60 seconds [ 0.185618] audit: initializing netlink socket (disabled) [ 0.185636] type=2000 audit(1324031376.183:1): initialized [ 0.192097] HugeTLB registered 4 MB page size, pre-allocated 0 pages [ 0.192221] VFS: Disk quotas dquot_6.5.2 [ 0.192251] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.192308] msgmni has been set to 980 [ 0.192503] alg: No test for stdrng (krng) [ 0.192593] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) [ 0.192597] io scheduler noop registered [ 0.192599] io scheduler anticipatory registered [ 0.192616] io scheduler cfq registered (default) [ 0.192767] alloc irq_desc for 24 on node -1 [ 0.192770] alloc kstat_irqs on node -1 [ 0.192780] pcieport 0000:00:1c.0: irq 24 for MSI/MSI-X [ 0.192789] pcieport 0000:00:1c.0: setting latency timer to 64 [ 0.193024] alloc irq_desc for 25 on node -1 [ 0.193026] alloc kstat_irqs on node -1 [ 0.193034] pcieport 0000:00:1c.1: irq 25 for MSI/MSI-X [ 0.193042] pcieport 0000:00:1c.1: setting latency timer to 64 [ 0.193524] vesafb: framebuffer at 0xe0000000, mapped to 0xe0000000, using 3750k, total 7872k [ 0.193527] vesafb: mode is 800x600x16, linelength=1600, pages=7 [ 0.193529] vesafb: scrolling: redraw [ 0.193532] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 [ 0.201144] Console: switching to colour frame buffer device 100x37 [ 0.207587] fb0: VESA VGA frame buffer device [ 0.207766] isapnp: Scanning for PnP cards... [ 0.517403] isapnp: No Plug & Play device found [ 0.586112] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 0.586276] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.586551] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 0.587650] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 0.588349] 00:07: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 0.591000] brd: module loaded [ 0.591080] input: Macintosh mouse button emulation as /devices/virtual/input/input0 [ 0.591214] Fixed MDIO Bus: probed [ 0.591361] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 [ 0.593815] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 0.593821] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 0.594368] mice: PS/2 mouse device common for all mice [ 0.594561] EISA: Probing bus 0 at eisa.0 [ 0.594614] cpuidle: using governor ladder [ 0.594617] cpuidle: using governor menu [ 0.594960] TCP bic registered [ 0.595039] Using IPI No-Shortcut mode [ 0.611252] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1 [ 0.614864] registered taskstats version 1 [ 0.615173] Freeing unused kernel memory: 540k freed [ 0.615386] Write protecting the kernel text: 3172k [ 0.615415] Write protecting the kernel read-only data: 1340k [ 1.046912] SCSI subsystem initialized [ 1.092945] libata version 3.00 loaded. [ 1.102129] ata_piix 0000:00:1f.1: version 2.13 [ 1.102147] alloc irq_desc for 18 on node -1 [ 1.102149] alloc kstat_irqs on node -1 [ 1.102157] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 1.102195] ata_piix 0000:00:1f.1: setting latency timer to 64 [ 1.102947] scsi0 : ata_piix [ 1.103577] scsi1 : ata_piix [ 1.105088] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 [ 1.105092] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 [ 1.105135] alloc irq_desc for 19 on node -1 [ 1.105137] alloc kstat_irqs on node -1 [ 1.105144] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 1.105149] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ] [ 1.105188] ata_piix 0000:00:1f.2: setting latency timer to 64 [ 1.105571] scsi2 : ata_piix [ 1.106720] scsi3 : ata_piix [ 1.108336] ata3: SATA max UDMA/133 cmd 0xe080 ctl 0xe000 bmdma 0xd800 irq 19 [ 1.108340] ata4: SATA max UDMA/133 cmd 0xdc00 ctl 0xd880 bmdma 0xd808 irq 19 [ 1.285896] ata3.00: ATA-7: SAMSUNG HD161HJ, JF100-19, max UDMA7 [ 1.285900] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 0/32) [ 1.292307] ata3.00: configured for UDMA/133 [ 1.292425] scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD161HJ JF10 PQ: 0 ANSI: 5 [ 1.293127] sd 2:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB) [ 1.293174] sd 2:0:0:0: [sda] Write Protect is off [ 1.293177] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1.293200] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1.293347] sda: sda1 sda2 sda4 < sda5 > [ 1.328147] sd 2:0:0:0: [sda] Attached SCSI disk [ 2.309419] PM: Starting manual resume from disk [ 2.331817] kjournald starting. Commit interval 5 seconds [ 2.331830] EXT3-fs: mounted filesystem with writeback data mode. [ 4.010465] sd 2:0:0:0: Attached scsi generic sg0 type 0 [ 4.063083] input: PC Speaker as /devices/platform/pcspkr/input/input2 [ 4.092222] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded [ 4.092244] r8169 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 4.092289] r8169 0000:02:00.0: setting latency timer to 64 [ 4.092345] alloc irq_desc for 26 on node -1 [ 4.092348] alloc kstat_irqs on node -1 [ 4.092363] r8169 0000:02:00.0: irq 26 for MSI/MSI-X [ 4.092617] eth0: RTL8101e at 0xe0598000, 00:1d:92:b8:3a:49, XID 94200000 IRQ 26 [ 4.230094] Linux agpgart interface v0.103 [ 4.320217] psmouse serio1: ID: 10 00 64 [ 4.324252] processor LNXCPU:00: registered as cooling_device0 [ 4.480743] usbcore: registered new interface driver usbfs [ 4.480770] usbcore: registered new interface driver hub [ 4.484588] usbcore: registered new device driver usb [ 4.486098] uhci_hcd: USB Universal Host Controller Interface driver [ 4.486149] alloc irq_desc for 23 on node -1 [ 4.486152] alloc kstat_irqs on node -1 [ 4.486159] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 4.486169] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 4.486173] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 4.486200] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 4.486233] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000e880 [ 4.486270] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.486272] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.486275] usb usb1: Product: UHCI Host Controller [ 4.486277] usb usb1: Manufacturer: Linux 2.6.32-std-def-alt20.M50P.1 uhci_hcd [ 4.486280] usb usb1: SerialNumber: 0000:00:1d.0 [ 4.486419] usb usb1: configuration #1 chosen from 1 choice [ 4.486451] hub 1-0:1.0: USB hub found [ 4.486460] hub 1-0:1.0: 2 ports detected [ 4.486519] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 4.486527] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 4.486530] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 4.486538] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 4.486562] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000e800 [ 4.486592] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.486595] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.486597] usb usb2: Product: UHCI Host Controller [ 4.486599] usb usb2: Manufacturer: Linux 2.6.32-std-def-alt20.M50P.1 uhci_hcd [ 4.486602] usb usb2: SerialNumber: 0000:00:1d.1 [ 4.486702] usb usb2: configuration #1 chosen from 1 choice [ 4.486731] hub 2-0:1.0: USB hub found [ 4.486739] hub 2-0:1.0: 2 ports detected [ 4.486795] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 4.486802] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 4.486805] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 4.486814] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 4.486848] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e480 [ 4.486879] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.486881] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.486884] usb usb3: Product: UHCI Host Controller [ 4.486886] usb usb3: Manufacturer: Linux 2.6.32-std-def-alt20.M50P.1 uhci_hcd [ 4.486889] usb usb3: SerialNumber: 0000:00:1d.2 [ 4.486988] usb usb3: configuration #1 chosen from 1 choice [ 4.487018] hub 3-0:1.0: USB hub found [ 4.487027] hub 3-0:1.0: 2 ports detected [ 4.487079] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 [ 4.487087] uhci_hcd 0000:00:1d.3: setting latency timer to 64 [ 4.487090] uhci_hcd 0000:00:1d.3: UHCI Host Controller [ 4.487098] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 [ 4.487129] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000e400 [ 4.487160] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.487162] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.487165] usb usb4: Product: UHCI Host Controller [ 4.487167] usb usb4: Manufacturer: Linux 2.6.32-std-def-alt20.M50P.1 uhci_hcd [ 4.487170] usb usb4: SerialNumber: 0000:00:1d.3 [ 4.487268] usb usb4: configuration #1 chosen from 1 choice [ 4.487298] hub 4-0:1.0: USB hub found [ 4.487306] hub 4-0:1.0: 2 ports detected [ 4.488902] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input3 [ 4.489009] ACPI: Power Button [PWRB] [ 4.489064] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input4 [ 4.489124] ACPI: Power Button [PWRF] [ 4.520979] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 4.625523] [drm] Initialized drm 1.1.0 20060810 [ 4.638175] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.638178] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after [ 4.638212] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 4.638238] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 4.638242] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 4.638259] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 [ 4.638275] ehci_hcd 0000:00:1d.7: using broken periodic workaround [ 4.638286] ehci_hcd 0000:00:1d.7: debug port 1 [ 4.642172] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 4.642182] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xcfe3bc00 [ 4.696344] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 4.696396] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002 [ 4.696399] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.696401] usb usb5: Product: EHCI Host Controller [ 4.696404] usb usb5: Manufacturer: Linux 2.6.32-std-def-alt20.M50P.1 ehci_hcd [ 4.696406] usb usb5: SerialNumber: 0000:00:1d.7 [ 4.696569] usb usb5: configuration #1 chosen from 1 choice [ 4.696667] hub 5-0:1.0: USB hub found [ 4.696678] hub 5-0:1.0: 8 ports detected [ 4.700289] agpgart-intel 0000:00:00.0: Intel 945G Chipset [ 4.700468] agpgart-intel 0000:00:00.0: detected 7932K stolen memory [ 4.702563] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xe0000000 [ 4.705207] rtc_cmos 00:03: RTC can wake from S4 [ 4.705336] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 [ 4.705366] rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs [ 4.707463] Floppy drive(s): fd0 is 1.44M [ 4.710914] parport_pc 00:09: reported by Plug and Play ACPI [ 4.710957] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 4.723762] FDC 0 is a post-1991 82077 [ 4.830449] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 4.830478] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 4.982735] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5 [ 5.008059] usb 5-5: new high speed USB device using ehci_hcd and address 2 [ 5.060295] hda_codec: ALC888: BIOS auto-probing. [ 5.061645] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input6 [ 5.065242] i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 5.065247] i915 0000:00:02.0: setting latency timer to 64 [ 5.077592] [drm] set up 7M of stolen space [ 5.078366] [drm] initialized overlay support [ 5.146852] usb 5-5: New USB device found, idVendor=0bda, idProduct=8187 [ 5.146856] usb 5-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 5.146859] usb 5-5: Product: RTL8187_Wireless [ 5.146861] usb 5-5: Manufacturer: Manufacturer_Realtek_RTL8187_ [ 5.146863] usb 5-5: SerialNumber: 00E04C6D1EE3 [ 5.147031] usb 5-5: configuration #1 chosen from 1 choice [ 5.359043] ppdev: user-space parallel port driver [ 5.520248] [drm:edid_is_valid] ERROR* EDID checksum is invalid, remainder is 167 [ 5.520252] [drm:edid_is_valid] ERROR Raw EDID: [ 5.520255] <3>00 ff ff ff ff ff ff 00 04 72 2f 00 84 7b 20 82 .........r/..{ . [ 5.520258] <3>16 12 01 03 6c 22 1b 78 2a 3d 85 a6 56 4a 9a 24 ....l".x=..VJ.$ [ 5.520260] <3>12 50 54 bf ef 00 61 46 71 40 71 4f 81 00 81 40 .PT...aFq@qO...@ [ 5.520263] <3>81 4a 81 4f 81 80 30 2a 00 98 51 00 2a 40 30 70 .J.O..0..Q.@0p [ 5.520265] <3>13 00 52 0e 11 00 00 1e 00 00 00 fd 00 31 4b 1e ..R..........1K. [ 5.520268] <3>50 0e a7 0a 20 20 20 20 20 20 00 00 00 fc 00 41 P... .....A [ 5.520270] <3>63 65 72 20 56 31 37 33 0a 20 20 20 00 00 00 ff cer V173. .... [ 5.520272] <3>00 4c 43 41 30 32 30 31 31 34 31 30 30 0a 00 f7 .LCA020114100... [ 5.520274] [ 5.520277] i915 0000:00:02.0: VGA-1: EDID invalid. [ 5.522358] fb: conflicting fb hw usage inteldrmfb vs VESA VGA - removing generic driver [ 5.522396] Console: switching to colour dummy device 80x25 [ 5.522604] fbcon: inteldrmfb (fb0) is primary device [ 5.522665] Console: switching to colour frame buffer device 100x37 [ 5.583032] [drm] DAC-6: set mode 800x600 14 [ 5.605404] fb0: inteldrmfb frame buffer device [ 5.605406] registered panic notifier [ 5.605414] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0 [ 5.663794] cfg80211: Using static regulatory domain info [ 5.663797] cfg80211: Regulatory domain: US [ 5.663799] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 5.663802] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 5.663805] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.663807] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.663810] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.663813] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 5.663815] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 5.663852] cfg80211: Calling CRDA for country: US [ 5.696529] usb 5-5: USB disconnect, address 2 [ 5.793596] usbcore: registered new interface driver rtl8187 [ 5.968062] usb 5-5: new high speed USB device using ehci_hcd and address 3 [ 6.010831] Adding 1004020k swap on /dev/sda1. Priority:-1 extents:1 across:1004020k [ 6.036296] hub 5-0:1.0: unable to enumerate USB device on port 5 [ 6.146589] EXT3 FS on sda2, internal journal [ 6.224340] hub 5-0:1.0: unable to enumerate USB device on port 5 [ 6.708021] usb 3-1: new full speed USB device using uhci_hcd and address 2 [ 6.874296] usb 3-1: New USB device found, idVendor=0bda, idProduct=8187 [ 6.874300] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 6.874303] usb 3-1: Product: RTL8187_Wireless [ 6.874305] usb 3-1: Manufacturer: Manufacturer_Realtek_RTL8187_ [ 6.874307] usb 3-1: SerialNumber: 00E04C6D1EE3 [ 6.874497] usb 3-1: configuration #1 chosen from 1 choice [ 8.038578] device-mapper: uevent: version 1.0.3 [ 8.039845] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com [ 8.142954] phy0: Selected rate control algorithm 'minstrel' [ 8.143244] phy0: hwaddr 00:e0:4c:6d:1e:e3, RTL8187vB (default) V1 + rtl8225z2, rfkill mask 2 [ 8.229463] rtl8187: Customer ID is 0x00 [ 8.229515] Registered led device: rtl8187-phy0::tx [ 8.229530] Registered led device: rtl8187-phy0::rx [ 8.232452] rtl8187: wireless switch is on [ 8.239632] udev: renamed network interface wlan0 to wlan1 [ 8.608863] kjournald starting. Commit interval 5 seconds [ 8.609052] EXT3 FS on sda5, internal journal [ 8.609058] EXT3-fs: mounted filesystem with writeback data mode. [ 14.438609] Bluetooth: Core ver 2.15 [ 14.440198] NET: Registered protocol family 31 [ 14.440201] Bluetooth: HCI device and connection manager initialized [ 14.440204] Bluetooth: HCI socket layer initialized [ 14.477601] Bluetooth: L2CAP ver 2.14 [ 14.477604] Bluetooth: L2CAP socket layer initialized [ 14.701911] Bluetooth: SCO (Voice Link) ver 0.6 [ 14.701914] Bluetooth: SCO socket layer initialized [ 14.741544] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 14.741547] Bluetooth: BNEP filters: protocol multicast [ 14.789083] Bridge firewalling registered [ 17.251970] RPC: Registered udp transport module. [ 17.251973] RPC: Registered tcp transport module. [ 17.251975] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 18.931798] r8169: eth0: link up [ 18.931806] r8169: eth0: link up [ 22.508674] [drm:edid_is_valid] ERROR* EDID checksum is invalid, remainder is 167 [ 22.508677] [drm:edid_is_valid] ERROR Raw EDID: [ 22.508680] <3>00 ff ff ff ff ff ff 00 04 72 2f 00 84 7b 20 82 .........r/..{ . [ 22.508683] <3>16 12 01 03 6c 22 1b 78 2a 3d 85 a6 56 4a 9a 24 ....l".x=..VJ.$ [ 22.508686] <3>12 50 54 bf ef 00 61 46 71 40 71 4f 81 00 81 40 .PT...aFq@qO...@ [ 22.508688] <3>81 4a 81 4f 81 80 30 2a 00 98 51 00 2a 40 30 70 .J.O..0..Q.@0p [ 22.508691] <3>13 00 52 0e 11 00 00 1e 00 00 00 fd 00 31 4b 1e ..R..........1K. [ 22.508693] <3>50 0e a7 0a 20 20 20 20 20 20 00 00 00 fc 00 41 P... .....A [ 22.508695] <3>63 65 72 20 56 31 37 33 0a 20 20 20 00 00 00 ff cer V173. .... [ 22.508698] <3>00 4c 43 41 30 32 30 31 31 34 31 30 30 0a 00 f7 .LCA020114100... [ 22.508699] [ 22.508702] i915 0000:00:02.0: VGA-1: EDID invalid. [ 22.616822] [drm:edid_is_valid] ERROR* EDID checksum is invalid, remainder is 167 [ 22.616825] [drm:edid_is_valid] ERROR Raw EDID: [ 22.616828] <3>00 ff ff ff ff ff ff 00 04 72 2f 00 84 7b 20 82 .........r/..{ . [ 22.616831] <3>16 12 01 03 6c 22 1b 78 2a 3d 85 a6 56 4a 9a 24 ....l".x=..VJ.$ [ 22.616833] <3>12 50 54 bf ef 00 61 46 71 40 71 4f 81 00 81 40 .PT...aFq@qO...@ [ 22.616835] <3>81 4a 81 4f 81 80 30 2a 00 98 51 00 2a 40 30 70 .J.O..0..Q.@0p [ 22.616838] <3>13 00 52 0e 11 00 00 1e 00 00 00 fd 00 31 4b 1e ..R..........1K. [ 22.616840] <3>50 0e a7 0a 20 20 20 20 20 20 00 00 00 fc 00 41 P... .....A [ 22.616843] <3>63 65 72 20 56 31 37 33 0a 20 20 20 00 00 00 ff cer V173. .... [ 22.616845] <3>00 4c 43 41 30 32 30 31 31 34 31 30 30 0a 00 f7 .LCA020114100... [ 22.616847] [ 22.616850] i915 0000:00:02.0: VGA-1: EDID invalid. [ 22.717573] [drm] DAC-6: set mode 1280x1024 16 [ 24.734905] NET: Registered protocol family 17 [ 28.316763] [drm:edid_is_valid] ERROR* EDID checksum is invalid, remainder is 167 [ 28.316767] [drm:edid_is_valid] ERROR Raw EDID: [ 28.316771] <3>00 ff ff ff ff ff ff 00 04 72 2f 00 84 7b 20 82 .........r/..{ . [ 28.316773] <3>16 12 01 03 6c 22 1b 78 2a 3d 85 a6 56 4a 9a 24 ....l".x=..VJ.$ [ 28.316776] <3>12 50 54 bf ef 00 61 46 71 40 71 4f 81 00 81 40 .PT...aFq@qO...@ [ 28.316778] <3>81 4a 81 4f 81 80 30 2a 00 98 51 00 2a 40 30 70 .J.O..0..Q.@0p [ 28.316780] <3>13 00 52 0e 11 00 00 1e 00 00 00 fd 00 31 4b 1e ..R..........1K. [ 28.316783] <3>50 0e a7 0a 20 20 20 20 20 20 00 00 00 fc 00 41 P... .....A [ 28.316785] <3>63 65 72 20 56 31 37 33 0a 20 20 20 00 00 00 ff cer V173. .... [ 28.316788] <3>00 4c 43 41 30 32 30 31 31 34 31 30 30 0a 00 f7 .LCA020114100... [ 28.316789] [ 28.316793] i915 0000:00:02.0: VGA-1: EDID invalid. [ 28.560916] [drm:edid_is_valid] ERROR* EDID checksum is invalid, remainder is 167 [ 28.560920] [drm:edid_is_valid] ERROR Raw EDID: [ 28.560923] <3>00 ff ff ff ff ff ff 00 04 72 2f 00 84 7b 20 82 .........r/..{ . [ 28.560926] <3>16 12 01 03 6c 22 1b 78 2a 3d 85 a6 56 4a 9a 24 ....l".x=..VJ.$ [ 28.560929] <3>12 50 54 bf ef 00 61 46 71 40 71 4f 81 00 81 40 .PT...aFq@qO...@ [ 28.560931] <3>81 4a 81 4f 81 80 30 2a 00 98 51 00 2a 40 30 70 .J.O..0..Q.@0p [ 28.560933] <3>13 00 52 0e 11 00 00 1e 00 00 00 fd 00 31 4b 1e ..R..........1K. [ 28.560936] <3>50 0e a7 0a 20 20 20 20 20 20 00 00 00 fc 00 41 P... .....A [ 28.560938] <3>63 65 72 20 56 31 37 33 0a 20 20 20 00 00 00 ff cer V173. .... [ 28.560940] <3>00 4c 43 41 30 32 30 31 31 34 31 30 30 0a 00 f7 .LCA020114100... [ 28.560942] [ 28.560945] i915 0000:00:02.0: VGA-1: EDID invalid. [ 28.732767] [drm:edid_is_valid] ERROR* EDID checksum is invalid, remainder is 167 [ 28.732770] [drm:edid_is_valid] ERROR Raw EDID: [ 28.732774] <3>00 ff ff ff ff ff ff 00 04 72 2f 00 84 7b 20 82 .........r/..{ . [ 28.732777] <3>16 12 01 03 6c 22 1b 78 2a 3d 85 a6 56 4a 9a 24 ....l".x=..VJ.$ [ 28.732780] <3>12 50 54 bf ef 00 61 46 71 40 71 4f 81 00 81 40 .PT...aFq@qO...@ [ 28.732782] <3>81 4a 81 4f 81 80 30 2a 00 98 51 00 2a 40 30 70 .J.O..0..Q.@0p [ 28.732785] <3>13 00 52 0e 11 00 00 1e 00 00 00 fd 00 31 4b 1e ..R..........1K. [ 28.732787] <3>50 0e a7 0a 20 20 20 20 20 20 00 00 00 fc 00 41 P... .....A [ 28.732790] <3>63 65 72 20 56 31 37 33 0a 20 20 20 00 00 00 ff cer V173. .... [ 28.732792] <3>00 4c 43 41 30 32 30 31 31 34 31 30 30 0a 00 f7 .LCA020114100... [ 28.732794] [ 28.732798] i915 0000:00:02.0: VGA-1: EDID invalid. [ 28.981804] vboxdrv: Trying to deactivate the NMI watchdog permanently... [ 28.981808] vboxdrv: Warning: 2.6.31+ kernel detected. Most likely the hardware performance [ 28.981809] vboxdrv: counter framework which can generate NMIs is active. You have to prevent [ 28.981810] vboxdrv: the usage of hardware performance counters by [ 28.981811] vboxdrv: echo 2 > /proc/sys/kernel/perf_counter_paranoid [ 28.981814] vboxdrv: Found 1 processor cores. [ 28.982031] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'. [ 28.982034] vboxdrv: Successfully loaded version 3.2.4_OSE (interface 0x00140001). [ 31.554069] bootsplash 3.1.6-2004/03/31: looking for picture... [ 31.554231] bootsplash: error while decompressing picture: depth mismatch (15) [ 43.256835] [drm:edid_is_valid] ERROR* EDID checksum is invalid, remainder is 167 [ 43.256838] [drm:edid_is_valid] ERROR Raw EDID: [ 43.256842] <3>00 ff ff ff ff ff ff 00 04 72 2f 00 84 7b 20 82 .........r/..{ . [ 43.256845] <3>16 12 01 03 6c 22 1b 78 2a 3d 85 a6 56 4a 9a 24 ....l".x=..VJ.$ [ 43.256847] <3>12 50 54 bf ef 00 61 46 71 40 71 4f 81 00 81 40 .PT...aFq@qO...@ [ 43.256850] <3>81 4a 81 4f 81 80 30 2a 00 98 51 00 2a 40 30 70 .J.O..0..Q.@0p [ 43.256852] <3>13 00 52 0e 11 00 00 1e 00 00 00 fd 00 31 4b 1e ..R..........1K. [ 43.256855] <3>50 0e a7 0a 20 20 20 20 20 20 00 00 00 fc 00 41 P... .....A [ 43.256857] <3>63 65 72 20 56 31 37 33 0a 20 20 20 00 00 00 ff cer V173. .... [ 43.256860] <3>00 4c 43 41 30 32 30 31 31 34 31 30 30 0a 00 f7 .LCA020114100... [ 43.256862] [ 43.256864] i915 0000:00:02.0: VGA-1: EDID invalid. [ 44.824762] [drm:edid_is_valid] ERROR* EDID checksum is invalid, remainder is 167 [ 44.824766] [drm:edid_is_valid] ERROR Raw EDID: [ 44.824770] <3>00 ff ff ff ff ff ff 00 04 72 2f 00 84 7b 20 82 .........r/..{ . [ 44.824772] <3>16 12 01 03 6c 22 1b 78 2a 3d 85 a6 56 4a 9a 24 ....l".x=..VJ.$ [ 44.824775] <3>12 50 54 bf ef 00 61 46 71 40 71 4f 81 00 81 40 .PT...aFq@qO...@ [ 44.824777] <3>81 4a 81 4f 81 80 30 2a 00 98 51 00 2a 40 30 70 .J.O..0..Q.@0p [ 44.824780] <3>13 00 52 0e 11 00 00 1e 00 00 00 fd 00 31 4b 1e ..R..........1K. [ 44.824782] <3>50 0e a7 0a 20 20 20 20 20 20 00 00 00 fc 00 41 P... .....A [ 44.824785] <3>63 65 72 20 56 31 37 33 0a 20 20 20 00 00 00 ff cer V173. .... [ 44.824787] <3>00 4c 43 41 30 32 30 31 31 34 31 30 30 0a 00 f7 .LCA020114100... [ 44.824789] [ 44.824792] i915 0000:00:02.0: VGA-1: EDID invalid. [ 44.932786] [drm:edid_is_valid] ERROR* EDID checksum is invalid, remainder is 167 [ 44.932790] [drm:edid_is_valid] ERROR Raw EDID: [ 44.932794] <3>00 ff ff ff ff ff ff 00 04 72 2f 00 84 7b 20 82 .........r/..{ . [ 44.932796] <3>16 12 01 03 6c 22 1b 78 2a 3d 85 a6 56 4a 9a 24 ....l".x=..VJ.$ [ 44.932799] <3>12 50 54 bf ef 00 61 46 71 40 71 4f 81 00 81 40 .PT...aFq@qO...@ [ 44.932801] <3>81 4a 81 4f 81 80 30 2a 00 98 51 00 2a 40 30 70 .J.O..0..Q.*@0p [ 44.932804] <3>13 00 52 0e 11 00 00 1e 00 00 00 fd 00 31 4b 1e ..R..........1K. [ 44.932806] <3>50 0e a7 0a 20 20 20 20 20 20 00 00 00 fc 00 41 P... .....A [ 44.932809] <3>63 65 72 20 56 31 37 33 0a 20 20 20 00 00 00 ff cer V173. .... [ 44.932811] <3>00 4c 43 41 30 32 30 31 31 34 31 30 30 0a 00 f7 .LCA020114100... [ 44.932813] [ 44.932816] i915 0000:00:02.0: VGA-1: EDID inval

Список: 1-25 из 35

1 2

Войдите чтобы ответить на тему