1. был установлен Альт 5.0.1 Мастер

2. подключаю проектор... и, никакого эффекта (пробовал нажать спец комбинацю "FN+F5" - не помогло)

3. перезагрузился с включенным проектором: на процессе загрузки (когда бегунок голубенький движется) проектор показывает изображение, как только доходит до конца - проектор отрубается, и на мониторе ноубука появляется выбор пользователей

конфиг ноутбука (everest)

Тип ЦП  - Mobile Intel Celeron 550, 2000 MHz (15 x 133)
Системная плата  - Mitac Notebook PC
Чипсет системной платы  - VIA VN896
Системная память  - 896 Мб (DDR2-667 DDR2 SDRAM)

Видеоадаптер  - VIA Chrome9 HC

Производитель MiTAC
Продукт Notebook PC
  Версия VT6363A

пробовал "xorg.conf" править - не, получилось, откатился к бэкапу

может логи пригодятся

xorg.conf:

 Section "ServerLayout"
Identifier "Minimal layout"
Screen "Screen0" 0 0
EndSection

Section "Module"
SubSection "extmod"
Option "omit xfree86-dga"
EndSubSection
EndSection

Section "Monitor"
Identifier "Monitor0|0"
EndSection

Section "Device"
Identifier "Card0|0"
Driver "openchrome"
EndSection

Section "Screen"
Identifier "Screen0"
Device "Card0|0"
Monitor "Monitor0|0"
DefaultDepth 16
SubSection "Display"
Modes "1024x768" "1024x736" "1024x600" "960x720" "848x480" "832x624" "800x600" "720x576" "640x480"
EndSubSection
EndSection

dmesg:

[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.30-std-def-alt15 (builder@apiary.orion.altlinux.org) (gcc version 4.3.2 20081105 (ALT Linux 4.3.2-alt13) (GCC) ) #1 SMP Mon Dec 14 08:45:48 UTC 2009
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] NSC Geode by NSC
[ 0.000000] Cyrix CyrixInstead
[ 0.000000] Centaur CentaurHauls
[ 0.000000] Transmeta GenuineTMx86
[ 0.000000] Transmeta TransmetaCPU
[ 0.000000] UMC UMC UMC UMC
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000d0000 - 00000000000d4000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 0000000037e80000 (usable)
[ 0.000000] BIOS-e820: 0000000037e80000 - 0000000037e95000 (ACPI data)
[ 0.000000] BIOS-e820: 0000000037e95000 - 0000000037f00000 (ACPI NVS)
[ 0.000000] BIOS-e820: 0000000037f00000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] DMI present.
[ 0.000000] Phoenix BIOS detected: BIOS may corrupt low RAM, working around it.
[ 0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[ 0.000000] last_pfn = 0x37e80 max_arch_pfn = 0x100000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-C7FFF write-protect
[ 0.000000] C8000-DFFFF uncachable
[ 0.000000] E0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 000000000 mask FC0000000 write-back
[ 0.000000] 1 base 037F00000 mask FFFF00000 uncachable
[ 0.000000] 2 base 038000000 mask FF8000000 uncachable
[ 0.000000] 3 disabled
[ 0.000000] 4 disabled
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] Scanning 0 areas for low memory corruption
[ 0.000000] modified physical RAM map:
[ 0.000000] modified: 0000000000000000 - 0000000000010000 (reserved)
[ 0.000000] modified: 0000000000010000 - 000000000009f800 (usable)
[ 0.000000] modified: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] modified: 00000000000d0000 - 00000000000d4000 (reserved)
[ 0.000000] modified: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] modified: 0000000000100000 - 0000000037e80000 (usable)
[ 0.000000] modified: 0000000037e80000 - 0000000037e95000 (ACPI data)
[ 0.000000] modified: 0000000037e95000 - 0000000037f00000 (ACPI NVS)
[ 0.000000] modified: 0000000037f00000 - 0000000040000000 (reserved)
[ 0.000000] modified: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] modified: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] modified: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] modified: 00000000fff00000 - 0000000100000000 (reserved)
[ 0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[ 0.000000] 0000000000 - 0000400000 page 4k
[ 0.000000] 0000400000 - 0037400000 page 2M
[ 0.000000] 0037400000 - 00377fe000 page 4k
[ 0.000000] kernel direct mapping tables up to 377fe000 @ 10000-15000
[ 0.000000] RAMDISK: 00e6a000 - 00eff8c8
[ 0.000000] ACPI: RSDP 000f8510 00024 (v02 PTLTD )
[ 0.000000] ACPI: XSDT 37e8f564 0004C (v01 PTLTD XSDT 06040000 LTP 00000000)
[ 0.000000] ACPI: FACP 37e94e74 000F4 (v03 VN896 PTLTW 06040000 PTL_ 000F4240)
[ 0.000000] ACPI: DSDT 37e90e8a 03F76 (v01 VIA PTL_ACPI 06040000 MSFT 03000001)
[ 0.000000] ACPI: FACS 37e95fc0 00040
[ 0.000000] ACPI: APIC 37e94f68 0005C (v01 PTLTD APIC 06040000 LTP 00000000)
[ 0.000000] ACPI: MCFG 37e94fc4 0003C (v01 PTLTD MCFG 06040000 LTP 00000000)
[ 0.000000] ACPI: SSDT 37e90972 00518 (v01 PmRef Cpu0Cst 00003001 INTL 20050228)
[ 0.000000] ACPI: SSDT 37e8f5b0 013C2 (v01 PmRef CpuPm 00003000 INTL 20050228)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] 6MB HIGHMEM available.
[ 0.000000] 887MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 377fe000
[ 0.000000] low ram: 0 - 377fe000
[ 0.000000] node 0 low ram: 00000000 - 377fe000
[ 0.000000] node 0 bootmap 00011000 - 00017f00
[ 0.000000] (9 early reservations) ==> bootmem [0000000000 - 00377fe000]
[ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
[ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
[ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
[ 0.000000] #3 [0000200000 - 0000744168] TEXT DATA BSS ==> [0000200000 - 0000744168]
[ 0.000000] #4 [0000e6a000 - 0000eff8c8] RAMDISK ==> [0000e6a000 - 0000eff8c8]
[ 0.000000] #5 [000009f800 - 0000100000] BIOS reserved ==> [000009f800 - 0000100000]
[ 0.000000] #6 [0000745000 - 0000748170] BRK ==> [0000745000 - 0000748170]
[ 0.000000] #7 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
[ 0.000000] #8 [0000011000 - 0000018000] BOOTMAP ==> [0000011000 - 0000018000]
[ 0.000000] found SMP MP-table at [c00f85c0] f85c0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000010 -> 0x00001000
[ 0.000000] Normal 0x00001000 -> 0x000377fe
[ 0.000000] HighMem 0x000377fe -> 0x00037e80
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0x00000010 -> 0x0000009f
[ 0.000000] 0: 0x00000100 -> 0x00037e80
[ 0.000000] On node 0 totalpages: 228879
[ 0.000000] free_area_init_node: node 0, pgdat c0621fe0, node_mem_map c1000200
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 3951 pages, LIFO batch:0
[ 0.000000] Normal zone: 1744 pages used for memmap
[ 0.000000] Normal zone: 221486 pages, LIFO batch:31
[ 0.000000] HighMem zone: 14 pages used for memmap
[ 0.000000] HighMem zone: 1652 pages, LIFO batch:0
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x4008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfecc0000] gsi_base[24])
[ 0.000000] IOAPIC[1]: apic_id 2, version 3, address 0xfecc0000, GSI 24-47
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] ACPI: IRQ10 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 2 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] SMP: Allowing 1 CPUs, 0 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 48
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d0000
[ 0.000000] PM: Registered nosave memory: 00000000000d0000 - 00000000000d4000
[ 0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 11 pages at c1704000, static data 21820 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 227089
[ 0.000000] Kernel command line: auto BOOT_IMAGE=ALTLinux ro root=UUID=a77a6627-2b74-4a3d-89f2-dde687d03e26 resume=/dev/disk/by-uuid/2d635ad7-6047-48da-a71d-cb41c8cff2cc panic=30 splash=silent quiet=1
[ 0.000000] bootsplash: silent mode.
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] Experimental hierarchical RCU implementation.
[ 0.000000] Experimental hierarchical RCU init done.
[ 0.000000] NR_IRQS:2304 nr_irqs:256
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Fast TSC calibration using PIT
[ 0.000000] Detected 1994.985 MHz processor.
[ 0.004000] Console: colour dummy device 80x25
[ 0.004000] console [tty0] enabled
[ 0.004000] ram_console: buffer (null), invalid size 0, datasize 4294967284
[ 0.004000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.004000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.004000] allocated 4579520 bytes of page_cgroup
[ 0.004000] please try cgroup_disable=memory option if you don't want
[ 0.004000] Initializing HighMem for node 0 (000377fe:00037e80)
[ 0.004000] Memory: 896816k/915968k available (2862k kernel code, 18532k reserved, 1415k data, 460k init, 6664k highmem)
[ 0.004000] virtual kernel memory layout:
[ 0.004000] fixmap : 0xffe16000 - 0xfffff000 (1956 kB)
[ 0.004000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.004000] vmalloc : 0xf7ffe000 - 0xff7fe000 ( 120 MB)
[ 0.004000] lowmem : 0xc0000000 - 0xf77fe000 ( 887 MB)
[ 0.004000] .init : 0xc0635000 - 0xc06a8000 ( 460 kB)
[ 0.004000] .data : 0xc04cb87d - 0xc062d828 (1415 kB)
[ 0.004000] .text : 0xc0200000 - 0xc04cb87d (2862 kB)
[ 0.004000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.004011] Calibrating delay loop (skipped), value calculated using timer frequency.. 3989.97 BogoMIPS (lpj=7979940)
[ 0.004049] Security Framework initialized
[ 0.004055] SELinux: Disabled at boot.
[ 0.004068] Mount-cache hash table entries: 512
[ 0.004183] Initializing cgroup subsys ns
[ 0.004187] Initializing cgroup subsys cpuacct
[ 0.004191] Initializing cgroup subsys memory
[ 0.004198] Initializing cgroup subsys devices
[ 0.004200] Initializing cgroup subsys freezer
[ 0.004202] Initializing cgroup subsys net_cls
[ 0.004221] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.004224] CPU: L2 cache: 1024K
[ 0.004228] Intel machine check architecture supported.
[ 0.004231] Intel machine check reporting enabled on CPU#0.
[ 0.004234] using mwait in idle threads.
[ 0.004242] Checking 'hlt' instruction... OK.
[ 0.020566] SMP alternatives: switching to UP code
[ 0.025620] Freeing SMP alternatives: 19k freed
[ 0.025628] ACPI: Core revision 20090320
[ 0.036566] ..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
[ 0.040001] ..MP-BIOS bug: 8254 timer not connected to IO-APIC
[ 0.040001] ...trying to set up timer (IRQ0) through the 8259A ...
[ 0.040001] ..... (found apic 0 pin 0) ...
[ 0.081730] ....... works.
[ 0.081732] CPU0: Intel(R) Celeron(R) M CPU 550 @ 2.00GHz stepping 01
[ 0.084001] Brought up 1 CPUs
[ 0.084001] Total of 1 processors activated (3989.97 BogoMIPS).
[ 0.084001] CPU0 attaching NULL sched-domain.
[ 0.084001] net_namespace: 1088 bytes
[ 0.084001] regulator: core version 0.5
[ 0.084001] NET: Registered protocol family 16
[ 0.084001] EISA bus registered
[ 0.084001] ACPI: bus type pci registered
[ 0.084001] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 6
[ 0.084001] PCI: MCFG area at e0000000 reserved in E820
[ 0.084001] PCI: Using MMCONFIG for extended config space
[ 0.084001] PCI: Using configuration type 1 for base access
[ 0.084001] bio: create slab <bio-0> at 0
[ 0.084001] ACPI: EC: Enabling special treatment for EC from MSI.
[ 0.084001] ACPI: EC: Look up EC in DSDT
[ 0.087542] ACPI: Interpreter enabled
[ 0.087551] ACPI: (supports S0 S3 S4 S5)
[ 0.087568] ACPI: Using IOAPIC for interrupt routing
[ 0.089200] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.096616] ACPI: EC: GPE = 0x5, I/O: command/status = 0x66, data = 0x62
[ 0.096619] ACPI: EC: driver started in interrupt mode
[ 0.097383] ACPI: No dock devices found.
[ 0.097395] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.097474] pci 0000:00:00.0: reg 10 32bit mmio: [0xc0000000-0xc7ffffff]
[ 0.098026] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
[ 0.098030] pci 0000:00:02.0: PME# disabled
[ 0.098110] pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
[ 0.098115] pci 0000:00:03.0: PME# disabled
[ 0.098188] pci 0000:00:0f.0: reg 10 io port: [0x4cb0-0x4cb7]
[ 0.098196] pci 0000:00:0f.0: reg 14 io port: [0x4ca4-0x4ca7]
[ 0.098203] pci 0000:00:0f.0: reg 18 io port: [0x4ca8-0x4caf]
[ 0.098211] pci 0000:00:0f.0: reg 1c io port: [0x4ca0-0x4ca3]
[ 0.098218] pci 0000:00:0f.0: reg 20 io port: [0x4c80-0x4c8f]
[ 0.098226] pci 0000:00:0f.0: reg 24 io port: [0x4400-0x44ff]
[ 0.098307] pci 0000:00:0f.1: reg 20 io port: [0x4c90-0x4c9f]
[ 0.098400] pci 0000:00:10.0: reg 20 io port: [0x4c00-0x4c1f]
[ 0.098429] pci 0000:00:10.0: supports D1 D2
[ 0.098431] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.098435] pci 0000:00:10.0: PME# disabled
[ 0.098490] pci 0000:00:10.1: reg 20 io port: [0x4c20-0x4c3f]
[ 0.098519] pci 0000:00:10.1: supports D1 D2
[ 0.098521] pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.098526] pci 0000:00:10.1: PME# disabled
[ 0.098580] pci 0000:00:10.2: reg 20 io port: [0x4c40-0x4c5f]
[ 0.098610] pci 0000:00:10.2: supports D1 D2
[ 0.098611] pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.098616] pci 0000:00:10.2: PME# disabled
[ 0.098671] pci 0000:00:10.3: reg 20 io port: [0x4c60-0x4c7f]
[ 0.098700] pci 0000:00:10.3: supports D1 D2
[ 0.098702] pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.098706] pci 0000:00:10.3: PME# disabled
[ 0.098741] pci 0000:00:10.4: reg 10 32bit mmio: [0xcb300000-0xcb3000ff]
[ 0.098790] pci 0000:00:10.4: supports D1 D2
[ 0.098792] pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.098796] pci 0000:00:10.4: PME# disabled
[ 0.098991] pci 0000:00:12.0: reg 10 io port: [0x4800-0x48ff]
[ 0.098999] pci 0000:00:12.0: reg 14 32bit mmio: [0xcb300400-0xcb3004ff]
[ 0.099043] pci 0000:00:12.0: supports D1 D2
[ 0.099045] pci 0000:00:12.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.099050] pci 0000:00:12.0: PME# disabled
[ 0.099257] pci 0000:01:00.0: reg 10 32bit mmio: [0xa0000000-0xbfffffff]
[ 0.099264] pci 0000:01:00.0: reg 14 32bit mmio: [0xc9000000-0xc9ffffff]
[ 0.099287] pci 0000:01:00.0: reg 30 32bit mmio: [0x000000-0x00ffff]
[ 0.099309] pci 0000:01:00.0: supports D1 D2
[ 0.099357] pci 0000:00:01.0: bridge 32bit mmio: [0xc9000000-0xc9ffffff]
[ 0.099362] pci 0000:00:01.0: bridge 32bit mmio pref: [0xa0000000-0xbfffffff]
[ 0.099414] pci 0000:00:02.0: bridge io port: [0x5000-0x6fff]
[ 0.099419] pci 0000:00:02.0: bridge 32bit mmio: [0xca000000-0xca7fffff]
[ 0.099426] pci 0000:00:02.0: bridge 64bit mmio pref: [0xc8000000-0xc87fffff]
[ 0.099479] pci 0000:00:03.0: bridge io port: [0x7000-0x8fff]
[ 0.099483] pci 0000:00:03.0: bridge 32bit mmio: [0xca800000-0xcaffffff]
[ 0.099491] pci 0000:00:03.0: bridge 64bit mmio pref: [0xc8800000-0xc8ffffff]
[ 0.099534] pci 0000:06:01.0: reg 10 64bit mmio: [0xcb000000-0xcb003fff]
[ 0.099580] pci 0000:06:01.0: PME# supported from D0 D3hot D3cold
[ 0.099584] pci 0000:06:01.0: PME# disabled
[ 0.099640] pci 0000:00:13.0: bridge 32bit mmio: [0xcb000000-0xcb0fffff]
[ 0.099694] pci 0000:00:13.1: transparent bridge
[ 0.099729] pci_bus 0000:00: on NUMA node 0
[ 0.099734] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.100054] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGC._PRT]
[ 0.100111] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE0C._PRT]
[ 0.100177] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SP2P._PRT]
[ 0.100263] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P2PE._PRT]
[ 0.114161] ACPI: PCI Interrupt Link [ALKA] (IRQs 16 17 18 19 20 21 22 23) *9, disabled.
[ 0.114257] ACPI: PCI Interrupt Link [ALKB] (IRQs 16 17 18 19 20 21 22 23) *10, disabled.
[ 0.114350] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *11, disabled.
[ 0.114440] ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *3, disabled.
[ 0.114558] ACPI: PCI Interrupt Link [LNKA] (IRQs *9 10 11 12)
[ 0.114676] ACPI: PCI Interrupt Link [LNKB] (IRQs 9 *10 11 12)
[ 0.114792] ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11 12)
[ 0.114907] ACPI: PCI Interrupt Link [LNKD] (IRQs 9 10 11 12) *3
[ 0.115269] PCI: Using ACPI for IRQ routing
[ 0.115486] NetLabel: Initializing
[ 0.115488] NetLabel: domain hash size = 128
[ 0.115489] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.115501] NetLabel: unlabeled traffic allowed by default
[ 0.115595] pnp: PnP ACPI init
[ 0.115603] ACPI: bus type pnp registered
[ 0.119362] pnp: PnP ACPI: found 10 devices
[ 0.119365] ACPI: ACPI bus type pnp unregistered
[ 0.119370] PnPBIOS: Disabled by ACPI PNP
[ 0.119381] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved
[ 0.119384] system 00:01: iomem range 0xf0012000-0xf0012fff has been reserved
[ 0.119387] system 00:01: iomem range 0xf0013000-0xf0013fff has been reserved
[ 0.119395] system 00:06: iomem range 0x0-0x9ffff could not be reserved
[ 0.119398] system 00:06: iomem range 0xe0000-0xfffff could not be reserved
[ 0.119401] system 00:06: iomem range 0xfff00000-0xffffffff has been reserved
[ 0.119404] system 00:06: iomem range 0xffee0000-0xffefffff has been reserved
[ 0.119407] system 00:06: iomem range 0xfec00000-0xfec0ffff could not be reserved
[ 0.119410] system 00:06: iomem range 0xfee00000-0xfee0ffff could not be reserved
[ 0.119415] system 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 0.119419] system 00:07: ioport range 0xfe10-0xfe11 has been reserved
[ 0.119421] system 00:07: ioport range 0xfe00-0xfe00 has been reserved
[ 0.119424] system 00:07: ioport range 0x4000-0x407f has been reserved
[ 0.119427] system 00:07: ioport range 0x4100-0x411f has been reserved
[ 0.119430] system 00:07: ioport range 0x378-0x378 has been reserved
[ 0.119432] system 00:07: ioport range 0x37c-0x37c has been reserved
[ 0.119435] system 00:07: iomem range 0xffb00000-0xffedefff has been reserved
[ 0.154316] pci 0000:01:00.0: BAR 6: can't allocate mem resource [0xc0000000-0xbfffffff]
[ 0.154319] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[ 0.154321] pci 0000:00:01.0: IO window: disabled
[ 0.154327] pci 0000:00:01.0: MEM window: 0xc9000000-0xc9ffffff
[ 0.154331] pci 0000:00:01.0: PREFETCH window: 0x000000a0000000-0x000000bfffffff
[ 0.154338] pci 0000:00:02.0: PCI bridge, secondary bus 0000:02
[ 0.154341] pci 0000:00:02.0: IO window: 0x5000-0x6fff
[ 0.154347] pci 0000:00:02.0: MEM window: 0xca000000-0xca7fffff
[ 0.154351] pci 0000:00:02.0: PREFETCH window: 0x000000c8000000-0x000000c87fffff
[ 0.154358] pci 0000:00:03.0: PCI bridge, secondary bus 0000:04
[ 0.154361] pci 0000:00:03.0: IO window: 0x7000-0x8fff
[ 0.154367] pci 0000:00:03.0: MEM window: 0xca800000-0xcaffffff
[ 0.154372] pci 0000:00:03.0: PREFETCH window: 0x000000c8800000-0x000000c8ffffff
[ 0.154380] pci 0000:00:13.0: PCI bridge, secondary bus 0000:06
[ 0.154382] pci 0000:00:13.0: IO window: disabled
[ 0.154387] pci 0000:00:13.0: MEM window: 0xcb000000-0xcb0fffff
[ 0.154391] pci 0000:00:13.0: PREFETCH window: disabled
[ 0.154397] pci 0000:00:13.1: PCI bridge, secondary bus 0000:07
[ 0.154399] pci 0000:00:13.1: IO window: disabled
[ 0.154404] pci 0000:00:13.1: MEM window: disabled
[ 0.154408] pci 0000:00:13.1: PREFETCH window: disabled
[ 0.154424] pci 0000:00:01.0: setting latency timer to 64
[ 0.154433] alloc irq_desc for 27 on cpu 0 node 0
[ 0.154435] alloc kstat_irqs on cpu 0 node 0
[ 0.154439] pci 0000:00:02.0: PCI INT A -> GSI 27 (level, low) -> IRQ 27
[ 0.154444] pci 0000:00:02.0: setting latency timer to 64
[ 0.154452] alloc irq_desc for 31 on cpu 0 node 0
[ 0.154453] alloc kstat_irqs on cpu 0 node 0
[ 0.154457] pci 0000:00:03.0: PCI INT A -> GSI 31 (level, low) -> IRQ 31
[ 0.154461] pci 0000:00:03.0: setting latency timer to 64
[ 0.154469] pci 0000:00:13.0: setting latency timer to 64
[ 0.154475] pci 0000:00:13.1: setting latency timer to 64
[ 0.154480] pci_bus 0000:00: resource 0 io: [0x00-0xffff]
[ 0.154482] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
[ 0.154485] pci_bus 0000:01: resource 1 mem: [0xc9000000-0xc9ffffff]
[ 0.154487] pci_bus 0000:01: resource 2 pref mem [0xa0000000-0xbfffffff]
[ 0.154490] pci_bus 0000:02: resource 0 io: [0x5000-0x6fff]
[ 0.154492] pci_bus 0000:02: resource 1 mem: [0xca000000-0xca7fffff]
[ 0.154495] pci_bus 0000:02: resource 2 pref mem [0xc8000000-0xc87fffff]
[ 0.154498] pci_bus 0000:04: resource 0 io: [0x7000-0x8fff]
[ 0.154500] pci_bus 0000:04: resource 1 mem: [0xca800000-0xcaffffff]
[ 0.154503] pci_bus 0000:04: resource 2 pref mem [0xc8800000-0xc8ffffff]
[ 0.154505] pci_bus 0000:06: resource 1 mem: [0xcb000000-0xcb0fffff]
[ 0.154508] pci_bus 0000:07: resource 3 io: [0x00-0xffff]
[ 0.154510] pci_bus 0000:07: resource 4 mem: [0x000000-0xffffffff]
[ 0.154559] NET: Registered protocol family 2
[ 0.154647] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.154950] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.155558] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.156043] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.156047] TCP reno registered
[ 0.156233] NET: Registered protocol family 1
[ 0.156309] Trying to unpack rootfs image as initramfs...
[ 0.173821] Freeing initrd memory: 598k freed
[ 0.174658] Scanning for low memory corruption every 60 seconds
[ 0.174925] audit: initializing netlink socket (disabled)
[ 0.174945] type=2000 audit(1296572988.172:1): initialized
[ 0.180905] highmem bounce pool size: 64 pages
[ 0.180910] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 0.180967] VFS: Disk quotas dquot_6.5.2
[ 0.180993] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.181040] msgmni has been set to 1740
[ 0.181200] alg: No test for stdrng (krng)
[ 0.181263] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
[ 0.181266] io scheduler noop registered
[ 0.181268] io scheduler anticipatory registered
[ 0.181279] io scheduler cfq registered (default)
[ 0.181289] pci 0000:00:00.0: MSI quirk detected; MSI disabled
[ 0.181299] pci 0000:00:01.0: disabling DAC on VIA PCI bridge
[ 0.181383] pci 0000:01:00.0: Boot video device
[ 0.181524] pcieport-driver 0000:00:02.0: setting latency timer to 64
[ 0.181748] pcieport-driver 0000:00:03.0: setting latency timer to 64
[ 0.181983] aer 0000:00:02.0:pcie02: AER service couldn't init device: no _OSC support
[ 0.181989] aer 0000:00:03.0:pcie02: AER service couldn't init device: no _OSC support
[ 0.182179] vesafb: framebuffer at 0xa0000000, mapped to 0xf8080000, using 3750k, total 131072k
[ 0.182182] vesafb: mode is 800x600x16, linelength=1600, pages=31
[ 0.182184] vesafb: protected mode interface info at c000:a9de
[ 0.182187] vesafb: pmi: set display start = c00caa2c, set palette = c00caa9d
[ 0.182188] vesafb: scrolling: redraw
[ 0.182191] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
[ 0.182326] bootsplash 3.1.6-2004/03/31: looking for picture...
[ 0.189076] bootsplash: silentjpeg size 41759 bytes
[ 0.200605] bootsplash: ...found (800x600, 3864 bytes, v3).
[ 0.228185] Console: switching to colour frame buffer device 97x34
[ 0.264581] fb0: VESA VGA frame buffer device
[ 0.264790] isapnp: Scanning for PnP cards...
[ 0.575293] isapnp: No Plug & Play device found
[ 0.609851] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.612007] brd: module loaded
[ 0.612405] input: Macintosh mouse button emulation as /devices/virtual/input/input0
[ 0.612506] Fixed MDIO Bus: probed
[ 0.612597] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.614918] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 0.615898] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.615903] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.615906] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.615909] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.615911] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.616245] mice: PS/2 mouse device common for all mice
[ 0.616470] EISA: Probing bus 0 at eisa.0
[ 0.616513] cpuidle: using governor ladder
[ 0.616515] cpuidle: using governor menu
[ 0.616925] TCP bic registered
[ 0.616967] Using IPI No-Shortcut mode
[ 0.656045] Switched to high resolution mode on CPU 0
[ 0.657125] registered taskstats version 1
[ 0.657300] Freeing unused kernel memory: 460k freed
[ 0.657550] Write protecting the kernel text: 2864k
[ 0.657565] Write protecting the kernel read-only data: 1220k
[ 0.657594] Executing init=/init
[ 0.731010] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
[ 1.128838] SCSI subsystem initialized
[ 1.150638] Driver 'sd' needs updating - please use bus_type methods
[ 1.176200] libata version 3.00 loaded.
[ 1.186281] sata_via 0000:00:0f.0: version 2.4
[ 1.186298] alloc irq_desc for 21 on cpu 0 node 0
[ 1.186300] alloc kstat_irqs on cpu 0 node 0
[ 1.186307] sata_via 0000:00:0f.0: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[ 1.186341] sata_via 0000:00:0f.0: routed to hard irq line 10
[ 1.186668] scsi0 : sata_via
[ 1.186759] scsi1 : sata_via
[ 1.186790] ata1: SATA max UDMA/133 cmd 0x4cb0 ctl 0x4ca4 bmdma 0x4c80 irq 21
[ 1.186793] ata2: SATA max UDMA/133 cmd 0x4ca8 ctl 0x4ca0 bmdma 0x4c88 irq 21
[ 1.388014] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.601999] ata1.00: ATA-8: WDC WD1200BEVS-00UST0, 01.01A01, max UDMA/133
[ 1.602003] ata1.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.616661] ata1.00: configured for UDMA/133
[ 1.616784] scsi 0:0:0:0: Direct-Access ATA WDC WD1200BEVS-0 01.0 PQ: 0 ANSI: 5
[ 1.617020] sd 0:0:0:0: [sda] 234441648 512-byte hardware sectors: (120 GB/111 GiB)
[ 1.617034] sd 0:0:0:0: [sda] Write Protect is off
[ 1.617037] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.617056] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.617140] sda: sda1 sda4 < sda5 sda6 sda7 sda8 >
[ 1.674167] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.820013] ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
[ 1.841263] pata_acpi 0000:00:0f.1: power state changed by ACPI to D0
[ 1.851829] pata_via 0000:00:0f.1: version 0.3.4
[ 1.852285] scsi2 : pata_via
[ 1.852742] scsi3 : pata_via
[ 1.853478] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x4c90 irq 14
[ 1.853482] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x4c98 irq 15
[ 2.172379] ata4.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WA03, max UDMA/33
[ 2.188253] ata4.00: configured for UDMA/33
[ 2.193661] scsi 3:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20N WA03 PQ: 0 ANSI: 5
[ 3.264444] PM: Starting manual resume from disk
[ 3.322891] kjournald starting. Commit interval 5 seconds
[ 3.322901] EXT3-fs: mounted filesystem with writeback data mode.
[ 5.623097] input: PC Speaker as /devices/platform/pcspkr/input/input2
[ 5.692602] Driver 'sr' needs updating - please use bus_type methods
[ 5.695386] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.695423] sr 3:0:0:0: Attached scsi generic sg1 type 5
[ 5.704888] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.704895] Uniform CD-ROM driver Revision: 3.20
[ 5.705002] sr 3:0:0:0: Attached scsi CD-ROM sr0
[ 5.723067] thermal LNXTHERM:01: registered as thermal_zone0
[ 5.723077] ACPI: Thermal Zone [TZ0] (64 C)
[ 5.751642] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 5.751754] ACPI: Power Button [PWRF]
[ 5.751805] input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
[ 5.751836] ACPI: Sleep Button [SBTN]
[ 5.751876] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input5
[ 5.759362] ACPI: Lid Switch [LID]
[ 5.763686] acpi device:1a: registered as cooling_device0
[ 5.763798] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A03:00/device:18/device:19/input/input6
[ 5.763904] ACPI: Video Device [VGA0] (multi-head: yes rom: no post: no)
[ 5.804555] via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
[ 5.804597] alloc irq_desc for 23 on cpu 0 node 0
[ 5.804600] alloc kstat_irqs on cpu 0 node 0
[ 5.804607] via-rhine 0000:00:12.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[ 5.808772] eth0: VIA Rhine II at 0x14800, 00:40:d0:e6:96:4d, IRQ 23.
[ 5.809485] eth0: MII PHY found at address 1, status 0x7849 advertising 01e1 Link 0000.
[ 5.834916] Monitor-Mwait will be used to enter C-1 state
[ 5.834968] Monitor-Mwait will be used to enter C-2 state
[ 5.834977] Marking TSC unstable due to TSC halts in idle
[ 5.835032] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 5.835074] processor ACPI_CPU:00: registered as cooling_device1
[ 5.835079] ACPI: Processor [CPU0] (supports 16 throttling states)
[ 5.865468] usbcore: registered new interface driver usbfs
[ 5.865502] usbcore: registered new interface driver hub
[ 5.865531] usbcore: registered new device driver usb
[ 5.872988] uhci_hcd: USB Universal Host Controller Interface driver
[ 5.873046] alloc irq_desc for 20 on cpu 0 node 0
[ 5.873048] alloc kstat_irqs on cpu 0 node 0
[ 5.873055] uhci_hcd 0000:00:10.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[ 5.873065] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 5.873123] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 5.873156] uhci_hcd 0000:00:10.0: irq 20, io base 0x00004c00
[ 5.873192] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.873195] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.873197] usb usb1: Product: UHCI Host Controller
[ 5.873199] usb usb1: Manufacturer: Linux 2.6.30-std-def-alt15 uhci_hcd
[ 5.873202] usb usb1: SerialNumber: 0000:00:10.0
[ 5.873336] usb usb1: configuration #1 chosen from 1 choice
[ 5.873363] hub 1-0:1.0: USB hub found
[ 5.873369] hub 1-0:1.0: 2 ports detected
[ 5.873492] alloc irq_desc for 22 on cpu 0 node 0
[ 5.873495] alloc kstat_irqs on cpu 0 node 0
[ 5.873499] uhci_hcd 0000:00:10.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22
[ 5.873506] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 5.873525] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 5.873552] uhci_hcd 0000:00:10.1: irq 22, io base 0x00004c20
[ 5.873592] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.873595] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.873597] usb usb2: Product: UHCI Host Controller
[ 5.873599] usb usb2: Manufacturer: Linux 2.6.30-std-def-alt15 uhci_hcd
[ 5.873601] usb usb2: SerialNumber: 0000:00:10.1
[ 5.873670] usb usb2: configuration #1 chosen from 1 choice
[ 5.873693] hub 2-0:1.0: USB hub found
[ 5.873706] hub 2-0:1.0: 2 ports detected
[ 5.873826] uhci_hcd 0000:00:10.2: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 5.873833] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 5.873852] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 5.873873] uhci_hcd 0000:00:10.2: irq 21, io base 0x00004c40
[ 5.873901] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.873904] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.873906] usb usb3: Product: UHCI Host Controller
[ 5.873908] usb usb3: Manufacturer: Linux 2.6.30-std-def-alt15 uhci_hcd
[ 5.873911] usb usb3: SerialNumber: 0000:00:10.2
[ 5.873964] usb usb3: configuration #1 chosen from 1 choice
[ 5.873987] hub 3-0:1.0: USB hub found
[ 5.873993] hub 3-0:1.0: 2 ports detected
[ 5.874098] uhci_hcd 0000:00:10.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
[ 5.874105] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 5.874123] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 5.874150] uhci_hcd 0000:00:10.3: irq 23, io base 0x00004c60
[ 5.874178] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.874181] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.874183] usb usb4: Product: UHCI Host Controller
[ 5.874185] usb usb4: Manufacturer: Linux 2.6.30-std-def-alt15 uhci_hcd
[ 5.874187] usb usb4: SerialNumber: 0000:00:10.3
[ 5.874243] usb usb4: configuration #1 chosen from 1 choice
[ 5.874266] hub 4-0:1.0: USB hub found
[ 5.874272] hub 4-0:1.0: 2 ports detected
[ 5.877313] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.877317] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after
[ 5.877352] ehci_hcd 0000:00:10.4: PCI INT C -> GSI 21 (level, low) -> IRQ 21
[ 5.877370] ehci_hcd 0000:00:10.4: EHCI Host Controller
[ 5.877409] ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
[ 5.877442] ehci_hcd 0000:00:10.4: irq 21, io mem 0xcb300000
[ 5.888080] ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00
[ 5.888126] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[ 5.888129] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.888132] usb usb5: Product: EHCI Host Controller
[ 5.888134] usb usb5: Manufacturer: Linux 2.6.30-std-def-alt15 ehci_hcd
[ 5.888136] usb usb5: SerialNumber: 0000:00:10.4
[ 5.888291] usb usb5: configuration #1 chosen from 1 choice
[ 5.888324] hub 5-0:1.0: USB hub found
[ 5.888332] hub 5-0:1.0: 8 ports detected
[ 5.905340] Linux agpgart interface v0.103
[ 5.928158] ACPI: AC Adapter [AC] (on-line)
[ 6.015356] ACPI Warning (nspredef-0949): \_SB_.BAT0._BIF: Return Package type mismatch at index 9 - found [NULL Object Descriptor], expected String/Buffer [20090320]
[ 6.063078] ACPI: Battery Slot [BAT0] (battery present)
[ 6.140079] agpgart: Detected VIA P4M900 chipset
[ 6.147248] agpgart-via 0000:00:00.0: AGP aperture is 128M @ 0xc0000000
[ 6.152983] rtc_cmos 00:04: RTC can wake from S4
[ 6.153118] rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
[ 6.153156] rtc0: alarms up to one year, y3k, 242 bytes nvram
[ 6.198949] alloc irq_desc for 17 on cpu 0 node 0
[ 6.198953] alloc kstat_irqs on cpu 0 node 0
[ 6.198959] HDA Intel 0000:06:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[ 6.198992] HDA Intel 0000:06:01.0: setting latency timer to 64
[ 6.198997] HDA Intel 0000:06:01.0: PCI: Disallowing DAC for device
[ 6.200063] usb 5-3: new high speed USB device using ehci_hcd and address 2
[ 6.334670] usb 5-3: New USB device found, idVendor=0951, idProduct=1625
[ 6.334675] usb 5-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.334678] usb 5-3: Product: DT 101 II
[ 6.334680] usb 5-3: Manufacturer: Kingston
[ 6.334682] usb 5-3: SerialNumber: 0019E06B70FAA961D2CF0585
[ 6.334841] usb 5-3: configuration #1 chosen from 1 choice
[ 6.444040] usb 5-5: new high speed USB device using ehci_hcd and address 3
[ 6.562948] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x25a0b1, caps: 0xa04713/0x0
[ 6.582263] hda_codec: Unknown model for ALC268, trying auto-probe from BIOS...
[ 6.582336] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:13.0/0000:06:01.0/input/input7
[ 6.599512] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input8
[ 6.708935] usbcore: registered new interface driver libusual
[ 6.721642] Initializing USB Mass Storage driver...
[ 6.721757] scsi4 : SCSI emulation for USB Mass Storage devices
[ 6.721835] usbcore: registered new interface driver usb-storage
[ 6.721839] USB Mass Storage support registered.
[ 6.722490] usb-storage: device found at 2
[ 6.722493] usb-storage: waiting for device to settle before scanning
[ 6.752748] usb 5-5: New USB device found, idVendor=148f, idProduct=2573
[ 6.752753] usb 5-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.752756] usb 5-5: Product: 802.11 bg WLAN
[ 6.752758] usb 5-5: Manufacturer: Ralink
[ 6.752941] usb 5-5: configuration #1 chosen from 1 choice
[ 6.825036] cfg80211: Using static regulatory domain info
[ 6.825039] cfg80211: Regulatory domain: US
[ 6.825041] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 6.825044] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 6.825047] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.825050] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.825053] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.825055] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.825058] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 6.825067] cfg80211: Calling CRDA for country: US
[ 7.222670] phy0: Selected rate control algorithm 'minstrel'
[ 7.222904] Registered led device: rt73usb-phy0::radio
[ 7.222919] Registered led device: rt73usb-phy0::assoc
[ 7.222934] Registered led device: rt73usb-phy0::quality
[ 7.223485] usbcore: registered new interface driver rt73usb
[ 7.227148] usbcore: registered new interface driver rt2500usb
[ 8.449277] Adding 1791208k swap on /dev/sda6. Priority:-1 extents:1 across:1791208k
[ 8.887515] EXT3 FS on sda7, internal journal
[ 11.467796] device-mapper: uevent: version 1.0.3
[ 11.469272] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[ 11.720770] scsi 4:0:0:0: Direct-Access Kingston DT 101 II 1.00 PQ: 0 ANSI: 2
[ 11.721005] sd 4:0:0:0: Attached scsi generic sg2 type 0
[ 11.721244] usb-storage: device scan complete
[ 11.723381] sd 4:0:0:0: [sdb] 7831552 512-byte hardware sectors: (4.00 GB/3.73 GiB)
[ 11.724389] sd 4:0:0:0: [sdb] Write Protect is off
[ 11.724394] sd 4:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 11.724396] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 11.727636] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[ 11.727648] sdb: sdb1
[ 11.728646] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 12.828191] kjournald starting. Commit interval 5 seconds
[ 12.828449] EXT3 FS on sda8, internal journal
[ 12.828453] EXT3-fs: mounted filesystem with writeback data mode.
[ 12.900568] fuse init (API version 7.12)

Команда xrandr проектор заметила?

Такая же беда, ноут DELL

DELL Vostro 1510.

Уважаемая  Julia Dronova я жду с вашей тех.поддержки здесь )) http://www.spohelp.ru/forums/13-drayvery-i-linu...